The Forestry Forum is sponsored in part by:


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.


Sawmill & Woodlot Magazine



Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

BRUTE FORCE Authorized Dealer

Woodshax Outdoor Vending Solutions

FARMA


Council Tool

Baker Products

ECHO-Bearcat

Arborwear



Author Topic: New Mill Owner Questions  (Read 1495 times)

0 Members and 1 Guest are viewing this topic.

Offline plaindriver

  • Full Member
  • **
  • Posts: 97
  • Age: 66
  • Location: Crossville, Tn. on the Cumberland Plateau
  • Gender: Male
    • Share Post
New Mill Owner Questions
« on: July 03, 2013, 10:57:27 AM »
Neil, I just finished assembling my new Woodlands Mill. Almost everything is fine, except a few minor problems. The roller pin on the rt. cam lock for the head came out. In the sawdust somewhere. I temp replaced with a small screw/nut. The parts package was short (2) #10 nuts, tho there were about 8 extra M10x25 bolts.
But most importantly: your video on the 2013 mill shows a locking up-down head crank, where mine looks different, and has no locking mechanism. It has a tendency to vibrate lower during the cut. Is there a locking crank? Sure would be helpful.

Side note: I installed an Hr meter to track maint intervals. Cost about $10 on ebay. I mounted it to the lower lt of the motor.
 

 


  

 
Kubota L4600 DT w/FEL, John Deere 750 4WD w/FEL, PH Digger,RotoTiller,Box Scraper,Disc;16, 18, 20" chainsaws;Troy Built 27T splitter; table saw, radial arm saw,turning lathe, chipper, small backhoe, Isuzu NPR 14' stakeside diesel truck; a wife that still likes me.

Offline NeilB

  • Board Moderator
  • *****
  • Posts: 42
  • Location: Ontario, Canada
  • Gender: Male
    • Share Post
    • Woodland Portable Sawmills
Re: New Mill Owner Questions
« Reply #1 on: July 08, 2013, 11:18:28 AM »
Just saw this... getting parts UPS'd out as discussed earlier...
Neil B
Woodland Mills


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
Land owner sustainability questions

Started by grimmjohn on Forestry and Logging

21 Replies
4169 Views
Last post June 13, 2010, 11:07:38 PM
by Dieselbreath
xx
New mill owner

Started by AJ on Sawmills and Milling

10 Replies
2548 Views
Last post February 25, 2003, 11:36:59 AM
by dail_h
xx
New mill owner!!

Started by CDN-woodchuck on Sawmills and Milling

4 Replies
1364 Views
Last post September 27, 2006, 06:18:13 PM
by getoverit
xx
new mill owner

Started by sawguyver on Sawmills and Milling

21 Replies
3890 Views
Last post February 01, 2006, 12:34:39 PM
by sawguyver
 


Powered by EzPortal