The Forestry Forum is sponsored in part by:


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.


Sawmill & Woodlot Magazine



Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

BRUTE FORCE Authorized Dealer

Woodshax Outdoor Vending Solutions

FARMA


Council Tool

Baker Products

ECHO-Bearcat

Arborwear



Author Topic: 201 TJ winch  (Read 773 times)

0 Members and 1 Guest are viewing this topic.

Offline mog5858

  • Full Member
  • **
  • Posts: 54
  • Age: 32
  • Location: S.E sask S.W manitoba
  • Gender: Male
    • Share Post
201 TJ winch
« on: April 03, 2016, 12:39:53 PM »
 well trying to give my old girl a little more TLC and would like to get the winch to work a little better.  i works right good now free spools nice but slips when in a hard pull i would say over 3000 lb as i can pull more off of the draw bar hitch then i can winch by far. i really don't have and trees that would need more pull but i would like to get it right never know when it will have to pull me out of a somewhere lol. i get 7/16 on move met on the clutch disc when i snap the winch in place on the drum plates. i have made all new fingers as i thought that they maybe wore out but i not so sure now. this is a Braden winch made for TJ casting number is MS15-134 it's a manual engagement to over center the clutch fingers not sure how to go about adjusting it or if it need adjustment as it still snap over good and i could not get it much tighter with out having trouble to snap it over.  are my clutch disk wore out or do you think they are just glade up? can a guy take some sand paper to them to ruff them up a little?


Offline Neilo

  • Senior Member
  • ****
  • Posts: 394
  • Age: 41
  • Location: Australia
  • Gender: Male
    • Share Post
Re: 201 TJ winch
« Reply #1 on: April 03, 2016, 07:25:05 PM »
I would never sand those discs. They are made from asbestos.

They could be oily or dirty, or too thin and springs or something stopping full engagement.

The earliest workshop manual I have is from '65 and it talks about the Braden but only adjustment of the Hercules. It seems later Braden winches up until 64 were hydraulic clutch actuation.

Neilo

Offline Gearbox

  • Senior Member x2
  • *****
  • Posts: 1193
  • Age: 72
  • Location: North MN
  • Gender: Male
    • Share Post
Re: 201 TJ winch
« Reply #2 on: April 03, 2016, 08:47:15 PM »
try some lube on the clutch slide and then see if you can tighten it up some . It looks dry in the pic .
A bunch of chainsaws a BT6870 processer , TC 5 International track skidder and not near enough time

Offline mog5858

  • Full Member
  • **
  • Posts: 54
  • Age: 32
  • Location: S.E sask S.W manitoba
  • Gender: Male
    • Share Post
Re: 201 TJ winch
« Reply #3 on: April 09, 2016, 09:39:40 AM »
thanks boys i will take them out and give them a good clean and go from there and yes i will make sure my sliding caller is clean and well lubed.

Offline bushmechanic

  • Senior Member
  • ****
  • Posts: 857
  • Age: 47
  • Location: Milton,Newfoundland,Canada
  • Gender: Male
  • Someone else has it worse than you.
    • Share Post
Re: 201 TJ winch
« Reply #4 on: April 09, 2016, 03:47:12 PM »
Mog5858 I think that there is adjustment by means of a threaded collar which will increase or decrease the distance of the finger engagement. There's a lock pin where your black arrow is, I think you pull it out and make the adjustment by turning the finger hub, in for more pressure on the clutch and out to decrease it. Make sure that you put your lock pin back in a hole after adjustment.


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
hough IH S7 skidder with carco 100 winch.how do I adjust winch? manuals attached

Started by roundbarn on Forestry and Logging

5 Replies
936 Views
Last post February 15, 2016, 05:55:49 AM
by Logger RK
xx
Timberjack 208 winch valve section for hercules winch

Started by redneck on Forestry and Logging

10 Replies
3491 Views
Last post June 11, 2017, 02:50:40 AM
by Neilo
xx
440b winch driveline and winch questions

Started by ohiowoodchuck on Forestry and Logging

15 Replies
563 Views
Last post December 31, 2016, 02:46:51 PM
by ohiowoodchuck
xx
Winch cable for Farmi351 winch

Started by fireman05 on Forestry and Logging

5 Replies
2065 Views
Last post April 23, 2007, 08:04:17 PM
by thecfarm
 


Powered by EzPortal