The Forestry Forum is sponsored in part by:


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Forest Products Industry Insurance


Norwood Industries Inc.


Sawmill & Woodlot Magazine



Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

BRUTE FORCE Authorized Dealer

Woodshax Outdoor Vending Solutions

FARMA


Council Tool

Baker Products

ECHO-Bearcat

Arborwear



Author Topic: 2017 sawmill shootout results  (Read 383 times)

0 Members and 1 Guest are viewing this topic.

Offline mad murdock

  • Senior Member x2
  • *****
  • Posts: 3400
  • Age: 53
  • Location: NW OREGON Near Carlton.
  • Gender: Male
  • The woods is the best "office"!
    • Share Post
2017 sawmill shootout results
« on: October 12, 2017, 12:32:07 PM »
Jake, let us know details on how it turned out.  Looks like the mill you took to Ohio was decked out with longer feet, and a bigger engine.  Did you use the turbokerf blade on it? 
Thanks for the awesome vid!
JD AMT 626, Turbosawmill M6 Warrior Ultra liteweight, Granberg Alaskan III, lots of saws-gas powered and human powered :D

Offline NZJake

  • Board Moderator
  • *****
  • Posts: 221
  • Age: 39
  • Location: NZ
  • Gender: Male
    • Share Post
    • 12 X 12 CUT MONO RAIL SWINGBLADE SAWMILL
Re: 2017 sawmill shootout results
« Reply #1 on: October 26, 2017, 11:56:15 PM »
Hi Mad murdock,

Unfortunately we had what we thought was issues with saw-blade.

I took them back to the factory and found that they clocked well. Turns out it was hub damage caused by a potential major bump in freight causing miss-alignment with the shaft. The crate may have been dropped as the bottom supports were almost non-existent.

At high RPM the blade wobbled significantly.

So I had to baby the mill through 4" cuts. Tried doing some deep 6" cuts but had to back out and take it all in smaller 4" depths.

Pretty disappointing really as I was expecting some amazing numbers. I've had to send out a replacement shaft and bearing kit to the new customer.

We did have the narrow kerf there but it didn't help any this time.

I'm thinking to replicate the shootout process at home here and have a live feed on our youtube channel with both the 6" Auto (same package) and a manual mill to give an actual representation of what should have happened.

I'm sure the production figures will still come in well enough for a one man team though. It also demonstrated well showing how easy it is to operate.

FYI...

Here is video taken at the show demonstrating what we were up against.


Here is video of what it should have looked like.

 
Wife says I woke up one morning half asleep uttering thin kerf and high production, I think I need a hobby other than milling?


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
Sawmill Shootout 2017 pregame

Started by 4x4American on Shows, Events and Places to meet

8 Replies
949 Views
Last post February 11, 2018, 08:31:14 AM
by dgdrls
moved
MOVED: Sawmill Shootout 2017 pregame

Started by chet on Sawmills and Milling

0 Replies
218 Views
Last post October 03, 2017, 10:32:58 PM
by chet
xx
sawmill shootout

Started by hansbaba on Sawmills and Milling

21 Replies
6731 Views
Last post May 31, 2007, 10:16:26 PM
by Cedarman
xx
Sawmill Shootout

Started by red on Shows, Events and Places to meet

1 Replies
376 Views
Last post August 13, 2017, 07:10:56 AM
by dgdrls
 


Powered by EzPortal