The Forestry Forum is sponsored in part by:


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.


Sawmill & Woodlot Magazine



Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

BRUTE FORCE Authorized Dealer

Woodshax Outdoor Vending Solutions

FARMA


Council Tool

Baker Products

ECHO-Bearcat

Arborwear



Author Topic: Husqvarna 236 help wanted  (Read 520 times)

0 Members and 1 Guest are viewing this topic.

Offline Dionvh

  • member
  • *
  • Posts: 2
  • I'm new!
    • Share Post
Husqvarna 236 help wanted
« on: November 16, 2017, 12:29:04 PM »
Hi there,
I took my Husqvarna 236 to the shop because it wasn't running properly. They checked it and the piston was damaged. Repair would be 400 (some other things too), and seeing as a piston set was 30 online I decided to do it myself. No problem, piston was easy to install but now I have to reassemble the chainsaw. The shop took it apart and gave it back in pieces so I have no documentation of how it should be put back together. I'm putting back the carb but now there are two fuel lines coming from the body, and the carb has two point to which I can connect fuel lines. Now the bulb also has fuel lines connected to it? I cannot figure out or find a diagram of which fuel line goes where. Can anybody help me with this? I have a picture but for some reason I cannot upload it.
Thanks!

Offline dougand3

  • Senior Member
  • ****
  • Posts: 379
  • Location: North Alabama
  • Gender: Male
    • Share Post
Re: Husqvarna 236 help wanted
« Reply #1 on: November 16, 2017, 03:25:07 PM »
Should be like a Poulan.
Fuel Pickup-line through hole under carb to carb nipple nearest to fuel pump side (1 big screw)
Other carb nipple-line to SHORT purge nipple.
LONG purge nipple line to tank hole in corner near clutch.
Husky: 272xp, 365, 261, 61, 55 (x3)
Stihl: 036, 026, 011AVT
Poulan: 4218, 2000

Offline Dionvh

  • member
  • *
  • Posts: 2
  • I'm new!
    • Share Post
Re: Husqvarna 236 help wanted
« Reply #2 on: November 17, 2017, 09:38:49 AM »
So if I understand correctly, there's 3 fuel lines?

Offline LeeB

  • Senior Member x2
  • *****
  • Posts: 7431
  • Age: 58
  • Location: Yellville Arkansas
  • Gender: Male
  • proud to be a TEXAN in Arkansas
    • Share Post
Re: Husqvarna 236 help wanted
« Reply #3 on: November 17, 2017, 09:58:32 AM »
You can find the manual here but you might need to put in a some more info than just 236 to find it.

http://www.husqvarna.com/us/support/download-manuals/
'98 LT40HDD/Lombardini, Case 580L, Cat D4C, JD 3032 tractor, JD 5410 tractor, Husky 346, 372 and 562XP's. Stihl MS180 and MS361, 1998 and 2006 3/4 Ton 5.9 Cummins 4x4's, 1989 Dodge D100 w/ 318, and a 1966 Chevy C60 w/ dump bed.

Offline LeeB

  • Senior Member x2
  • *****
  • Posts: 7431
  • Age: 58
  • Location: Yellville Arkansas
  • Gender: Male
  • proud to be a TEXAN in Arkansas
    • Share Post
Re: Husqvarna 236 help wanted
« Reply #4 on: November 17, 2017, 10:05:09 AM »
I find manuals for a 235 but not a 236.
'98 LT40HDD/Lombardini, Case 580L, Cat D4C, JD 3032 tractor, JD 5410 tractor, Husky 346, 372 and 562XP's. Stihl MS180 and MS361, 1998 and 2006 3/4 Ton 5.9 Cummins 4x4's, 1989 Dodge D100 w/ 318, and a 1966 Chevy C60 w/ dump bed.

Offline dougand3

  • Senior Member
  • ****
  • Posts: 379
  • Location: North Alabama
  • Gender: Male
    • Share Post
Re: Husqvarna 236 help wanted
« Reply #5 on: November 17, 2017, 11:19:00 AM »
Yes, 3 fuel lines.
1. fuel supply - 10-12" long with fuel pickup in tank.
2. Short purge line from carb - 4-5"
3. Long purge line to tank - 7-8"

The purge circuit is to pull air out of carb to replace with fuel - supplied by the fuel supply line.
You don't NEED a purge circuit for a good running saw. It's a fairly new invention for cold starts requiring a few less pulls.
Husky: 272xp, 365, 261, 61, 55 (x3)
Stihl: 036, 026, 011AVT
Poulan: 4218, 2000


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
Wanted: 50-56" bar for Husqvarna

Started by VPI on Wanted

0 Replies
225 Views
Last post January 23, 2018, 10:39:17 AM
by VPI
xx
Wanted husqvarna 61 white top cover

Started by symamania on Wanted

2 Replies
642 Views
Last post June 29, 2015, 06:50:57 AM
by thecfarm
xx
Scaffolding wanted - Jeff said it was ok to move to the wanted section

Started by kboilers on Wanted

5 Replies
1729 Views
Last post March 08, 2006, 09:08:20 AM
by thurlow
xx
Husqvarna 285CD & Husqvarna 375K concrete saw

Started by Coach on For Sale

2 Replies
1863 Views
Last post June 25, 2014, 12:30:04 AM
by hacknchop
 


Powered by EzPortal