iDRY Vacuum Kilns

Sponsors:

A review, have had a few questions about building older Husqvarna 61's into 272'

Started by weimedog, November 04, 2018, 09:36:04 AM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

weimedog

Husqvarna 365sp/372xpw Blend, Jonsered 2171 51.4mm XPW build,562xp HTSS, 560 HTSS, 272XP, 61/272XP, 555, 257, 242, 238, Homelite S-XL 925, XP-1020A, Super XL (Dad's saw); Jonsered 2094, Three 920's, CS-2172, Solo 603; 3 Huztl MS660's (2 54mm and 1 56mm)

mike_belben

Someone asked me a question about 61 into 72 and i totally forgot.  My bad. 
Praise The Lord

weimedog

Husqvarna 365sp/372xpw Blend, Jonsered 2171 51.4mm XPW build,562xp HTSS, 560 HTSS, 272XP, 61/272XP, 555, 257, 242, 238, Homelite S-XL 925, XP-1020A, Super XL (Dad's saw); Jonsered 2094, Three 920's, CS-2172, Solo 603; 3 Huztl MS660's (2 54mm and 1 56mm)

motzingg


weimedog

There was a thread we did way back a decade ago before doing the video's...that really dug into the details. Tried but couldn't find it...:( So those two are summaries...the one Bob and I did has good details if you have the patience to watch the later part. We also did one blending 272 with the Jonsered 670 and blended the different "pulse" configurations...I'll see if I can find that one as well. Its been a while! Maybe time for a "redux" on those 200's....
Husqvarna 365sp/372xpw Blend, Jonsered 2171 51.4mm XPW build,562xp HTSS, 560 HTSS, 272XP, 61/272XP, 555, 257, 242, 238, Homelite S-XL 925, XP-1020A, Super XL (Dad's saw); Jonsered 2094, Three 920's, CS-2172, Solo 603; 3 Huztl MS660's (2 54mm and 1 56mm)

huskywilson

nice video there , i got an old greytop 61 a long time ago , and eventually took it apart to do some resto on it and the piston ring land was a bit wide on the exhaust side so took the piston to a husky dealer and said do you have a 61 piston in stock , he replied i do but thats not it , i said yeah it is it s a1985 grey top 61 twin coil , he said no thats a 266xp piston and he measured it and said yip it s a 266 ,50mm single ring windowed piston , that whole topend will fit right onto a 61 chassis , must have been done by someone , hmmm ok do you have one , said yeah i do , went and got it and bought it , checked the cylinder and looked it up and it was a 266xp top end on it , and different manifold block and carb and intake and airfilter , did wonder why it run like a beast  :D ;D

thecfarm

Model 6020-20hp Manual Thomas bandsaw,TC40A 4wd 40 hp New Holland tractor, 450 Norse Winch, Heatmor 400 OWB,YCC 1978-79

huskywilson

thanks , i am on a couple of other forums , like my huskys , have 18 of them  8)

mike_belben

Yeah 61s are like a chevy 305.  What'll fit on top it?  Practically anything you want..  Is there a saw part that wont fit on it?  You can get lost in all the combos you can put on a 61 case if you have a few buckets of dead large bar huskys.  I bolt stuff on em that i dont even know what it came from or where i got it.  If it fits it ships chips!
Praise The Lord

Thank You Sponsors!