The Forestry Forum is sponsored in part by:

KNOW WHAT?
Between February 12, 2018 and June 18, 2018, this space displayed 13 Million, 871 Thousand and 87 times.



Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.


Sawmill & Woodlot Magazine



Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

BRUTE FORCE Authorized Dealer

Woodshax Outdoor Vending Solutions

FARMA


Council Tool

Baker Products

ECHO-Bearcat



Author Topic: Belsaw build  (Read 1538 times)

0 Members and 1 Guest are viewing this topic.

Offline glendaler

  • member
  • *
  • Posts: 29
  • Age: 30
  • Location: Nova Scotia, Canada
  • Gender: Male
  • I'm new!
    • Share Post
Re: Belsaw build
« Reply #20 on: June 12, 2018, 09:06:26 AM »
Ah, I wrongly assumed you just threw a bolt in. Did you select a long bolt to get enough shank to go through the whole axle holder and cut off the extra thread?

Offline Coolrunner

  • member
  • *
  • Posts: 10
  • Location: New Brunswick, Canada
  • Gender: Male
  • I'm new!
    • Share Post
Re: Belsaw build
« Reply #21 on: June 12, 2018, 11:39:28 AM »
I need the pawl repair too.  Mine slips if I try to go too fast or if sawdust has collected in the teeth.  BTW, I have been looking for another mill for the carriage parts to extend mine.  Otherwise I may build one.  
Kubota M6800, IH434,IH500C,MF130,JDMT, JD1010,FarmallA, Belsaw on busframe

Offline Flyingpig

  • member
  • *
  • Posts: 16
  • I'm new!
    • Share Post
Re: Belsaw build
« Reply #22 on: June 13, 2018, 08:06:48 PM »
Ya we were looking for whatever would be the easiest to switch out down the road with the lowest downtime. We did use longer bolts and trimmed the threads back.

Offline moodnacreek

  • Senior Member
  • ****
  • Posts: 514
  • Location: Orange County NY
  • Gender: Male
  • Sawin by the notches
    • Share Post
Re: Belsaw build
« Reply #23 on: June 13, 2018, 09:39:12 PM »
When I had a Bellsaw I put the reach rod in a 't' tube so you could twist it and rigged up a toggle and lever to the pawl. This rig is still working to day. It was just a bunch of junk brazed together and the pawl lasted much longer.

Offline glendaler

  • member
  • *
  • Posts: 29
  • Age: 30
  • Location: Nova Scotia, Canada
  • Gender: Male
  • I'm new!
    • Share Post
Re: Belsaw build
« Reply #24 on: June 15, 2018, 08:22:22 AM »
That's an interesting idea. What do you attribute the longer wear to? Were you turning the handle to disengage the pawl on the return strokes so it wasn't dragging on the ratchet wheel? Any pics?

Offline moodnacreek

  • Senior Member
  • ****
  • Posts: 514
  • Location: Orange County NY
  • Gender: Male
  • Sawin by the notches
    • Share Post
Re: Belsaw build
« Reply #25 on: June 15, 2018, 01:06:26 PM »
Glendalerl, yes, lifting the pawl at times.  Also put the feed outboard. There has to be a way to make a better setworks, ofte tthought about doing something with a large rachet  wrench.

Offline Babylon519

  • Full Member
  • **
  • Posts: 81
  • Age: 58
  • Location: Huron County, Ontario
  • Gender: Male
  • Circle Sawyer
    • Share Post
Re: Belsaw build
« Reply #26 on: June 15, 2018, 01:41:40 PM »
That pawl is a wear item we should probably team up and have a run of them made. I have I think 3, the one on the mill is about ready to be welded and ground, If I hold my mouth just right it grabs most of the time, the other two have been welded once and then worn down again.
x2. Mine is pretty rounded too. Add me to the order!
- Jason
Jason
1960 IH B-275 - same vintage as me!
1960 Circle Sawmill 42"
Stihl MS440 & a half-dozen other saws...


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
Custom 5hp Foley-Belsaw beam-planer on track system build.

Started by kastle on Sawmills and Milling

12 Replies
2153 Views
Last post March 25, 2014, 01:09:00 AM
by hardtailjohn
xx
M-14 Belsaw

Started by first shirt on Sawmills and Milling

4 Replies
1418 Views
Last post July 25, 2009, 07:24:09 AM
by bandmiller2
xx
Belsaw m14

Started by Mark K on Sawmills and Milling

7 Replies
3959 Views
Last post June 11, 2012, 03:45:43 PM
by Mark K
xx
might buy a Belsaw M-14

Started by KFhunter on Sawmills and Milling

5 Replies
711 Views
Last post July 24, 2017, 10:23:55 PM
by paul case
 


Powered by EzPortal