The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

FARMA


Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Baltic Abrasives Technologies Nyle Kiln Dry Systems




Author Topic: Drying black walnut slab  (Read 617 times)

0 Members and 1 Guest are viewing this topic.

Offline Jrhkc0812

  • Member*
  • *
  • Posts: 1
  • I'm new!
    • Share Post
Drying black walnut slab
« on: January 01, 2019, 08:42:51 PM »
Hi,

I currently have a black walnut slab air drying in the loft of my I heated garage in upstate NY. The slab is 2 thick, 20 wide and 12 feet long. It has been in the garage for two and half months and is at 35% moisture according to pinless meter.  I intend to use the slab as a bar top in the basement of my house. I am wondering if it is okay to move the slab to the heated basement of the house to finish drying or if it would be too aggressive and cause problems. Or is it okay to install the slab as bar top now as long as I dont finish and fasten it down? 

Offline WLC

  • Senior Member
  • ****
  • Posts: 403
  • Age: 54
  • Location: Wasilla, AK
  • Gender: Male
  • I'm new!
    • Share Post
Re: Drying black walnut slab
« Reply #1 on: January 01, 2019, 09:11:02 PM »
Firstly, welcome!!

Just from what I've gleaned here I would wait until it got down to 20% or lower before moving it inside.  I'm sure you will get someone with actual experience that will answer your question in a little while.
Woodmizer LT28
Branson 4wd tractor
Stihl chainsaws
Elbow grease.

Offline YellowHammer

  • Senior Member x2
  • *****
  • Posts: 3963
  • Age: 54
  • Location: New Market, Alabama
  • Gender: Male
  • Take Steps to Save Steps
    • Share Post
    • Hobby Hardwood Alabama
Re: Drying black walnut slab
« Reply #2 on: January 01, 2019, 10:10:44 PM »
I would leave the slab where it is, assuming it seems to be drying fine, until it reached the Fiber Saturation Point at about 25%, give or take.  Typically, I will air dry slabs until under 20% before I will even put them in a kiln.  
I personally use the rule of thumb that When the board reaches 20% moisture content, then 80% of the potential drying problems are in the past.
HobbyHardwoodAlabama.com

Offline Ianab

  • Administrator
  • *****
  • Posts: 13162
  • Age: 56
  • Location: Stratford , New Zealand
  • Gender: Male
  • Marmite on toast is a real breakfast
    • Share Post
Re: Drying black walnut slab
« Reply #3 on: January 02, 2019, 03:11:53 AM »
Moisture meters aren't accurate over about 30%, so it's likely 35% is the maximum your meter will read. It might actually be wetter. Also wood doesn't really start to shrink and move until it gets to the ~25% FSP that Yellowhammer mentioned.  Drying problems tend to occur if you dry too fast, so the outside of the wood gets too much below 25%, and the core is still green. Now the skin starts to shrink, and the core doesn't. So you have to dry slow enough for the moisture to move through the wood and escape. 

So I agree, wait until at least 20%, and I'd prefer more like 15% for a bit more safety. Even then, the board is till likely to move as it completes it's drying. But it should at least stay intact, even if it's not completely flat. 

In a perfect world you would want to get it down to 8-12%, depending on where you live. Then machine it flat, and it should stay that way.
Weekend warrior, Peterson JP test pilot, Dolmar 7900 and Stihl MS310 saws and  the usual collection of power tools :)


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
Black Walnut slab procedure

Started by GearDrive on Drying and Processing

4 Replies
989 Views
Last post January 07, 2016, 11:44:49 AM
by scsmith42
xx
Air Drying Black Walnut

Started by Gregfarley100 on Drying and Processing

10 Replies
1572 Views
Last post December 21, 2015, 10:28:52 PM
by Dough_baker
xx
Air Drying Ash and Black Walnut

Started by MarkOrge on Drying and Processing

3 Replies
801 Views
Last post April 02, 2018, 10:41:38 PM
by firefighter ontheside
xx
drying Black Walnut

Started by mmrz on Drying and Processing

17 Replies
5392 Views
Last post August 04, 2018, 09:05:37 AM
by Brad_bb
 


Powered by EzPortal