The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

FARMA


Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Baltic Abrasives Technologies Nyle Kiln Dry Systems




Author Topic: Husky Carb pre-heat flap/door-How critical is temp?  (Read 1132 times)

0 Members and 1 Guest are viewing this topic.

Offline outdoortype

  • member
  • *
  • Posts: 38
    • Share Post
Husky Carb pre-heat flap/door-How critical is temp?
« on: March 14, 2005, 09:41:25 PM »
  I read in the manual for my Husky 359 that when your cutting at or below 32 degrees F that you're supposed to open the flap/door in the cylinder cover to allow preheated air to pass into the carb & filter dept. to keep them from icing.  The air temp has varied a lot the last few times I've cut.  Yesterday it was 40-45 degrees F and I cut for 45 minutes before I realized that I left the flap/door open.  The saw ran fine.  I'm just wondering if I did any damage? Do I need to keep opening/closing the flap until the weather stabilizes? Thanks for your input.

Online Ianab

  • Administrator
  • *****
  • Posts: 13163
  • Age: 56
  • Location: Stratford , New Zealand
  • Gender: Male
  • Marmite on toast is a real breakfast
    • Share Post
Re: Husky Carb pre-heat flap/door-How critical is temp?
« Reply #1 on: March 14, 2005, 09:53:50 PM »
It's not critical, it's more a summer / winter thing. If it's real cold, you want to suck warm air off the engine to stop the carb icing up. If it's a hot day you want the coolest / densest air you can find to keep the mix right and the power up. At 40 deg neither setting should cause a problem.

Ian
Weekend warrior, Peterson JP test pilot, Dolmar 7900 and Stihl MS310 saws and  the usual collection of power tools :)

Offline Minnesota_boy

  • Senior Member x2
  • *****
  • Posts: 1773
  • Age: 67
  • Location: near Bemidji, Minnesota
  • Gender: Male
  • Some like 'em short, but I prefer looong!
    • Share Post
Re: Husky Carb pre-heat flap/door-How critical is temp?
« Reply #2 on: March 14, 2005, 09:56:40 PM »
In years past, there were no flaps and most of the time, carbs didn't ice up.  It takes certain specific conditions for carb icing to be of much concern.  On the other hand, having air preheated isn't much of a problem until the outside air is quite warm and I don't believe that 45 degrees fits that.

If I felt that carb icing could happen, I'd open that flap to preheat the air, but I wouldn't worry overmuch if I forgot until I noticed the saw running poorly.

The 32 degree thing is a part of the condition that is required for carb icing, so you don't need preheated air at temperatures above that.
I eat a high-fiber diet.  Lots of sawdust!


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
low temp carb adjustments

Started by 1953greg on Chainsaws

2 Replies
1342 Views
Last post February 24, 2005, 10:17:53 PM
by spencerhenry
xx
Temp Heat for the RV/shop

Started by Rougespear on Firewood and Wood Heating

19 Replies
1538 Views
Last post December 23, 2017, 02:15:27 PM
by Grizzly
xx
EC-2400 - no heat load, how long for water temp to drop?

Started by Bob Lentz on Firewood and Wood Heating

8 Replies
2285 Views
Last post April 08, 2012, 09:15:58 PM
by ParadisePA
xx
Husky 266-272 Tillotson carb ??

Started by Cut4fun on Chainsaws

7 Replies
3088 Views
Last post February 26, 2007, 02:35:47 PM
by Kevin
 


Powered by EzPortal