The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

FARMA


Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Baltic Abrasives Technologies Nyle Kiln Dry Systems




Author Topic: Shake  (Read 1219 times)

0 Members and 1 Guest are viewing this topic.

Offline Magicman

  • Senior Member x2
  • *****
  • Posts: 37992
  • Age: 75
  • Location: Brookhaven, MS
  • Gender: Male
  • A "Traveling Man"
    • Share Post
    • Knothole Sawmill
Shake
« on: July 09, 2010, 08:26:17 PM »
I'm sawing beetle killed SYP, but these trees were stressed by Hurricane Katrina.  I suspect that the internal stresses caused by Katrina will be with us for many years to come.  We'll blame it on beetles.
 


Shake rings.
Knothole Sawmill, LLC     '98 Wood-Mizer LT40SuperHydraulic   WM Million BF Club Member   WM Pro Sawyer Network

Never allow your "need" to make money to exceed your "desire" to provide quality service.....The Magicman

Offline Autocar

  • Senior Member x2
  • *****
  • Posts: 2865
  • Location: Twenty five miles southwest of Lima Ohio
  • Gender: Male
    • Share Post
Re: Shake
« Reply #1 on: July 09, 2010, 08:54:22 PM »
We find shake in Sycamores and cotton woods here in Ohio and some times after one H of a thunderstorm with straight line winds your find it in red oak and pin oak. White and Bur seems to hold togather a little better. But a tornado can do a number on all of them . I cut a white ash last fall that had a shake ring all the way around it and it was a inch thick so I left them dry out and knocked the centers out and made rustic waste paper cans.  :D
Bill

Offline woodmills1

  • Senior Member x2
  • *****
  • Posts: 5184
  • Age: 67
  • Location: Hudson, NH
  • Gender: Male
  • the truth shall set you free
    • Share Post
Re: Shake
« Reply #2 on: July 10, 2010, 05:26:47 PM »
shake always shows at one inch under the width you want  to cut


it is worse up here than rot, at least ya knows rot will be bad.

I have tried to cut shake trees..........red oak and hemlock..........it always shakes out one inch below my maketable width.

I DanG hate the shake
James Mills,Lovely wife,collect old tools,vacuuming fool,36 bdft/hr,oak paper cutter,ebonic yooper rapper nauga seller, Blue Ox? its not fast, 2 cat family, LT70,edger, 375 bd ft/hr, we like Bob,free heat,no oil 12 years,big splitter, baked stuffed lobster, still cuttin the logs dere IAM


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
Shake, ring shake, wind shake in timber

Started by pine on Sawmills and Milling

23 Replies
5299 Views
Last post June 13, 2014, 02:08:45 PM
by Ron Wenrich
xx
Shake Rat

Started by Gilman on Sawmills and Milling

5 Replies
2269 Views
Last post October 20, 2004, 10:56:07 PM
by Gilman
xx
Is this shake

Started by brdmkr on Sawmills and Milling

13 Replies
2499 Views
Last post May 04, 2007, 04:48:58 PM
by inspectorwoody
xx
shake

Started by laffs on Ask The Forester

7 Replies
1542 Views
Last post October 28, 2010, 06:38:45 PM
by laffs
 


Powered by EzPortal