The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

FARMA


Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems




Author Topic: Useing diesel as blade lube  (Read 2141 times)

0 Members and 1 Guest are viewing this topic.

Offline HD

  • member
  • *
  • Posts: 23
  • Location: arkansas
  • Gender: Male
    • Share Post
Useing diesel as blade lube
« on: December 21, 2010, 08:41:28 PM »
I was thinking about changeing over to diesel as a lube on my mill.  Right now I'm having a pitch problem.  After my cut I have to let the blade run a minute to clean the blade and then make my next cut.
I'm useing half a bottle of pinesol (16 oz)and a little dish liq added to 5 gallons of water. I've heard people using diesel and I just wondered if people are using reg or off road. Also does it prematurely ruin your belts and does it stain the wood your cutting?

Offline tyb525

  • Senior Member x2
  • *****
  • Posts: 3368
  • Age: 27
  • Location: Eastern Indiana
  • Gender: Male
  • Always learning.
    • Share Post
Re: Useing diesel as blade lube
« Reply #1 on: December 21, 2010, 08:46:15 PM »
I know some people use it, however the smell can remain on the boards, which could be a problem if you are sawing for other people. Also, consider where it will go if it doesn't go on the board...

Environmental and smell issues aside, I know the people the do use it seem to like it, but it takes much less of it than water. Just a drop every now and then.

Have you tried using more soap and/or increasing the flow?
LT10G10, Stihl 038 Magnum, many woodworking tools. Currently a farm service applicator, trying to find time to saw!

Offline ely

  • Senior Member x2
  • *****
  • Posts: 2700
  • Age: 52
  • Location: atoka okla.
  • Gender: Male
    • Share Post
Re: Useing diesel as blade lube
« Reply #2 on: December 21, 2010, 08:57:59 PM »
i have a squirt can that i lube the roller pads on my norwood with. i also use that same mix on my blade when i get a really pitchy log. i just turn the water off and give it a squirt as i cut. works well for me. i have not noticed any oil problems with the wood yet.
 btw it is 50% kerosene and baroil.

Offline paul case

  • Senior Member x2
  • *****
  • Posts: 4794
  • Age: 44
  • Location: extreeme northeast Oklahoma
  • Gender: Male
  • Original wearer of the PCM.
    • Share Post
Re: Useing diesel as blade lube
« Reply #3 on: December 21, 2010, 09:01:40 PM »
i use diesel. off road and even dirty or wash diesel works ok. cheaper the better. a drop every 4 or 5 seconds. i always shut it off when stopped to turn the log or offbear. if i cut 1000 bdft it might only take a quart. and no freezing. i am on my first set of belts and my mill has 400 hours on it so i would say that the belts are wearing normally. staining on the boards is minimal as well but i dont cut many mantle pieces or things that would be a problem on. pc
life is too short to be too serious. (some idiot)
2013 LT40SHE25 and Riehl edger,  WM 94 LT40 hd E15. Cut my sawing ''teeth'' on an EZ Boardwalk
sawing oak.hickory,ERC,walnut and almost anything else that shows up.
Don't get phylosophical with me. you will loose me for sure.
pc

Offline woodmills1

  • Senior Member x2
  • *****
  • Posts: 5184
  • Age: 68
  • Location: Hudson, NH
  • Gender: Male
  • the truth shall set you free
    • Share Post
Re: Useing diesel as blade lube
« Reply #4 on: December 21, 2010, 09:30:07 PM »
50 50 diesel and bar oil from a squirt  can as needed, only trouble is the quality of squirt cans today.
James Mills,Lovely wife,collect old tools,vacuuming fool,36 bdft/hr,oak paper cutter,ebonic yooper rapper nauga seller, Blue Ox? its not fast, 2 cat family, LT70,edger, 375 bd ft/hr, we like Bob,free heat,no oil 12 years,big splitter, baked stuffed lobster, still cuttin the logs dere IAM

Online ladylake

  • Senior Member x2
  • *****
  • Posts: 5015
  • Age: 67
  • Location: grey eagle mn
  • Gender: Male
  • I need to edit my profile!
    • Share Post
Re: Useing diesel as blade lube
« Reply #5 on: December 22, 2010, 05:11:43 AM »
Diesel in the winter, water in the summer. I'd run diesel all year if it did'nt  smell.   Steve
Timberking B20 14000 hours +  Case75xt grapple + forks+8" snow bucket + dirt bucket   770 Oliver   Lots(too many) of chainsaws, Like the Echo saws and the Stihl and Husky     W5  Case loader   1  trailers  Wright sharpener     Suffolk  setter Volvo MCT125c skid loader

Offline kelLOGg

  • Senior Member x2
  • *****
  • Posts: 2093
  • Age: 75
  • Location: Durham, NC
  • Gender: Male
  • More is better but enough is best
    • Share Post
Re: Useing diesel as blade lube
« Reply #6 on: December 22, 2010, 06:44:10 AM »
I use a diesel drip onto wipe pads. If I don't forget to turn it off I never smell it and no one has complained of the smell on the lumber. It is very effective even in small amounts. However, I do admire those who shun it for environmental reasons.
Cook's MP-32, 16HP, 20' (modified w/ power feed, up/down, loader/turner)
DH kiln, CatClaw, setter, tandem trailer, log arches, tractor, thumb tacks

Offline terrifictimbersllc

  • Senior Member x2
  • *****
  • Posts: 4599
  • Age: 65
  • Location: Mystic, CT
  • Gender: Male
    • Share Post
    • Terrific Timbers LLC
Re: Useing diesel as blade lube
« Reply #7 on: December 22, 2010, 06:57:28 AM »
I've used the Woodmizer additive for eastern pine at the recommended full strength and it works.  Doesn't smell. Don't have to have the lube flowing full speed either.  Tried dishwasher soap once and it worked too.  Pinesol a number of times with partial success but didnt get up to a pint or more per 5 gal yet.   Pinesol smells the best.
DJ Hoover, Terrific Timbers LLC,  Mystic CT Woodmizer Million Board Foot Club member. 2019 LT70 Super Wide, 2001 WM LT40SHDD (42HP Kubota, Accuset2, FAO's, Lubemizer, debarker),  Logrite fetching arch, WM BMS250 sharpener/BMT250 setter.  2001 F350 7.3L PSD 6 spd manual ZF 4x4 Crew Cab Long Bed

Offline Woodwalker

  • Senior Member
  • ****
  • Posts: 673
  • Age: 64
  • Location: Pine Valley (not on any maps)
  • Gender: Male
  • Old, ugly, rude, cude and sociability un-acceptable.
    • Share Post
Re: Useing diesel as blade lube
« Reply #8 on: December 22, 2010, 06:58:33 AM »
  Off road diesel here. Just a small drip. Determine the amount by watching the band for the pitch build up. I've never had any issues with smell. I've built rough pieces and finished projects out of both hard and soft wood where diesel was used as a lube with no staining problems.
Just cause your head's pointed, don't mean you are sharp.

Offline Kansas

  • In Memoriam
  • *
  • Posts: 5271
  • In the mountains of Kansas
    • Share Post
Re: Useing diesel as blade lube
« Reply #9 on: December 22, 2010, 07:00:44 AM »
We use diesel when we need it. We don't use water. We have tried just about everything, and diesel simply works better.

There is another alternative that might be good for those in a warmer clime. At one time, we tried bio-diesel. It was a bit more expensive that regular diesel, but didn't have the smell. (kind of smelled like McDonalds) Problem is, the stuff jells in the winter. In the end, it was just easier to grab regular diesel out of the tank.

Offline taylorsmissbeehaven

  • Senior Member
  • ****
  • Posts: 303
  • Age: 45
  • Location: Hillsborough,NC
  • Gender: Male
    • Share Post
Re: Useing diesel as blade lube
« Reply #10 on: December 22, 2010, 07:11:12 AM »
I have not used diesel but several of my friends in the mountains do. Lately I have been using  windshield wash fluid and have had good results. Hey KelLoGg good to see a neighboring sawyer on here. I'm in N. Durham Co. Maybe we could compare notes sometime. Brian
Opportunity is missed by most because it shows up wearing bib overalls and looks like work.

Offline Magicman

  • Senior Member x2
  • *****
  • Posts: 38218
  • Age: 76
  • Location: Brookhaven, MS
  • Gender: Male
  • A "Traveling Man"
    • Share Post
    • Knothole Sawmill
Re: Useing diesel as blade lube
« Reply #11 on: December 22, 2010, 08:55:20 AM »
HD, as stated above, many sawyers successfully use Diesel applied in different ways.  There is nothing wrong with experimenting to find the best lube for your use.

If you want to continue to use water mix, I would recommend 2oz of Cascade per gallon of water.  That mix figures out to 50 per 5 gallons.  In the Winter you will have to add a gallon of -32 windshield washer fluid to prevent freezing.

Cascade automatic dish washing liquid does not produce bubbles.  The generic that I tried didn't work well.

Knothole Sawmill, LLC     '98 Wood-Mizer LT40SuperHydraulic   WM Million BF Club Member   WM Pro Sawyer Network

Never allow your "need" to make money to exceed your "desire" to provide quality service.....The Magicman


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
Blade Lube.....Diesel????

Started by POSTON WIDEHEAD on Sawmills and Milling

6 Replies
1753 Views
Last post August 08, 2011, 07:39:41 AM
by bandmiller2
xx
Diesel Fuel for blade lube?

Started by epiphoneprs on Sawmills and Milling

24 Replies
8449 Views
Last post September 02, 2009, 06:52:04 AM
by Chico
xx
Diesel blade lube and rubber drive belts?

Started by Jhoff on Sawmills and Milling

7 Replies
982 Views
Last post April 20, 2018, 10:47:32 AM
by Jhoff
xx
Diesel for lube

Started by reswire on Sawmills and Milling

33 Replies
4087 Views
Last post January 26, 2016, 06:32:41 PM
by SineWave
 


Powered by EzPortal