The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.


Sawmill & Woodlot Magazine



Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

FARMA


Council Tool

Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon




Author Topic: Danuser MD5 post driver  (Read 1165 times)

0 Members and 1 Guest are viewing this topic.

Offline CX3

  • Senior Member
  • ****
  • Posts: 875
  • Age: 36
  • Location: SW Missouri
  • Gender: Male
    • Share Post
Danuser MD5 post driver
« on: April 12, 2018, 11:31:48 AM »
I have an older yellow danuser free fall post driver. It's the one with the little rubber wheel that lifts the pounding weight. Well the rubber is shot and they want 320 for a new one. The way my mind thinks is I could wrap some good rubber belting around it and use an epoxy to glue it down. Clamped tight with hose clamps until dry. Tell me why this won't work or..... a better idea? I really don't mind buying the part but I really think I can fix it??
John 3:16
You Better Believe It!

Offline CX3

  • Senior Member
  • ****
  • Posts: 875
  • Age: 36
  • Location: SW Missouri
  • Gender: Male
    • Share Post
Re: Danuser MD5 post driver
« Reply #1 on: April 29, 2018, 10:16:10 PM »
Well in case anyone ever searches it......i bought some 1/4" thick rubber discs from sloan.com.   They were for a grain bin auger. Anyhow the discs were 6"diameter which was just what I needed. I punched a center hole with a chassis punch on an iron worker. You could use any hydraulic punch for that matter.

I then stacked all the rubber discs and clamped them tight. I marked the holes with the hub from the original friction drive. Drill press was a good choice here. Drill them 1/2" because the rubber closes after the bit is removed.

I then took all the discs and replaced them on the hub.

OEM parts cost was actually $385. I bought the discs online and had some time in them for about $159.  Worked like a champ.
John 3:16
You Better Believe It!


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
Titan PGD3875 Gas Post driver

Started by LeeB on General Board

0 Replies
224 Views
Last post October 25, 2018, 09:32:08 AM
by LeeB
smiley
New Driver

Started by Paul_H on General Board

22 Replies
4540 Views
Last post September 05, 2002, 07:40:12 PM
by Paul_H
xx
My First Truck Driver... My Friend...

Started by AlexInman06 on Forestry and Logging

11 Replies
1242 Views
Last post December 30, 2012, 08:43:50 PM
by Meadows Miller
xx
Is she the youngest Case 580 B driver ever?

Started by MbfVA on Axe Woman Fan Forum

1 Replies
1841 Views
Last post August 16, 2017, 12:10:40 PM
by Savannahdan
 


Powered by EzPortal