The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

FARMA


Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Baltic Abrasives Technologies Nyle Kiln Dry Systems




Author Topic: monarch pump motors  (Read 895 times)

0 Members and 1 Guest are viewing this topic.

Offline woodmills1

  • Senior Member x2
  • *****
  • Posts: 5184
  • Age: 67
  • Location: Hudson, NH
  • Gender: Male
  • the truth shall set you free
    • Share Post
monarch pump motors
« on: March 31, 2019, 11:16:49 PM »
I replaced both monarch pump electric motors in my 2005 LT70.  The current replacements only differ by the addition of a ground strap.  So, I have two monarch part number 8058 circa 2005 from my woodmizer LT70 HD remote.  If these cores interest you please respond and understand this is only best offer to those interested.  The motors have 1818 hours and have never been brushed or repaired, one looks good and the other has a bit of commutator chew up.  The brushes are no longer sold by Woodmizer so they are cores for rebuild by a motor shop the makes its own brushes.  They owe me nothing so if they fit your needs contact me.  As always I will expect a good chunk of change to the forum even if the cost for the parts is short.
James Mills,Lovely wife,collect old tools,vacuuming fool,36 bdft/hr,oak paper cutter,ebonic yooper rapper nauga seller, Blue Ox? its not fast, 2 cat family, LT70,edger, 375 bd ft/hr, we like Bob,free heat,no oil 12 years,big splitter, baked stuffed lobster, still cuttin the logs dere IAM

Offline terrifictimbersllc

  • Senior Member x2
  • *****
  • Posts: 4564
  • Age: 65
  • Location: Mystic, CT
  • Gender: Male
    • Share Post
    • Terrific Timbers LLC
Re: monarch pump motors
« Reply #1 on: April 01, 2019, 05:56:06 AM »
Sure they're not Bosch?  Monarch hydraulic pumps for LT40 supers had Bosch motors and then went to Iskra.  
DJ Hoover, Terrific Timbers LLC,  Mystic CT Woodmizer Million Board Foot Club member.  2001 WM LT40SHDD (42HP Kubota, Accuset2, FAO's, Lubemizer, debarker),  Logrite fetching arch, WM BMS250 sharpener/BMT250 setter.  2001 F350 7.3L PSD 6 spd manual ZF 4x4 Crew Cab Long Bed

Offline woodmills1

  • Senior Member x2
  • *****
  • Posts: 5184
  • Age: 67
  • Location: Hudson, NH
  • Gender: Male
  • the truth shall set you free
    • Share Post
Re: monarch pump motors
« Reply #2 on: April 01, 2019, 02:11:09 PM »
there is a monarch logo and they say made for monarch hydraulics quality machining by jackoboice.  I replace them with Iskra
James Mills,Lovely wife,collect old tools,vacuuming fool,36 bdft/hr,oak paper cutter,ebonic yooper rapper nauga seller, Blue Ox? its not fast, 2 cat family, LT70,edger, 375 bd ft/hr, we like Bob,free heat,no oil 12 years,big splitter, baked stuffed lobster, still cuttin the logs dere IAM


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
Special Pump to Run OMR 315 Hydraulic Motors?

Started by R. Smith on Sawmills and Milling

3 Replies
961 Views
Last post August 19, 2014, 09:01:14 AM
by sealark37
xx
Hydraulic pump motors Uhm I fried em

Started by scully on Sawmills and Milling

13 Replies
1685 Views
Last post September 27, 2014, 09:49:25 PM
by barbender
xx
Monarch Aftermarket Brushes

Started by boman1 on Sawmills and Milling

17 Replies
2371 Views
Last post December 20, 2012, 09:05:21 PM
by MartyParsons
recycled
The Monarch Lightning Sawing Machine

Started by Jeff on General Board

15 Replies
1242 Views
Last post February 24, 2013, 03:19:04 PM
by SwampDonkey
 


Powered by EzPortal