The Forestry Forum is sponsored in part by:

KNOW WHAT?
Between February 12, 2018 and June 18, 2018, this space displayed 13 Million, 871 Thousand and 87 times.



Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.


Sawmill & Woodlot Magazine



Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

BRUTE FORCE Authorized Dealer

Woodshax Outdoor Vending Solutions

FARMA


Council Tool

Baker Products

ECHO-Bearcat



Author Topic: need some help/advice  (Read 1901 times)

0 Members and 1 Guest are viewing this topic.

Offline bad_boards

  • Full Member
  • **
  • Posts: 71
  • Location: edgewater, FL
  • Gender: Male
  • I'm new!
    • Share Post
need some help/advice
« on: September 29, 2006, 10:11:01 AM »
my craftsman rewide spring died
and it replaced it , now it snaps back nice
BUT the small spring out feet wont grab the plastic knob to turn the engine over

i took it back apart and the feet spring fine and the knob isnt worn at all

any ideas?

nm guys
i fixed it

but its still a craftsman , anyone have good at advice on fixing old remmingtons?

Offline SawTroll

  • Senior Member x2
  • *****
  • Posts: 2468
  • Age: 60
  • Location: Troms, North Norway
  • Gender: Male
    • Share Post
Re: need some help/advice
« Reply #1 on: September 29, 2006, 11:21:48 AM »
From what I have heard about them, Crapsmen with problems belong in the dumpster!    ???
Information collector.

Offline sawguy21

  • Senior Member x2
  • *****
  • Posts: 9394
  • Age: 69
  • Location: Enderby B.C. Canada
  • Gender: Male
    • Share Post
Re: need some help/advice
« Reply #2 on: September 29, 2006, 11:10:49 PM »
Did Remington make your Craftsman? Does it have the FM rewind with the spring loaded shoes and fiber washers? Check with a Stihl dealer, the early 08S and the 090's used the same system.
old age and treachery will always overcome youth and enthusiasm

Offline Mr Mom

  • Senior Member
  • ****
  • Posts: 794
  • Age: 44
  • Location: Ashtabula Ohio
  • Gender: Male
  • still alive!!!!
    • Share Post
Re: need some help/advice
« Reply #3 on: September 30, 2006, 04:05:09 AM »
     I have had my craftsmem for about 7years on and have had no problems.



     Thannks Alot Mr Mom

Offline SawTroll

  • Senior Member x2
  • *****
  • Posts: 2468
  • Age: 60
  • Location: Troms, North Norway
  • Gender: Male
    • Share Post
Re: need some help/advice
« Reply #4 on: September 30, 2006, 11:24:12 AM »
HA HA, I was just joking - it all depend on who made the Crapsman in question.
Information collector.

Offline twoodward15

  • Senior Member
  • ****
  • Posts: 620
  • Age: 43
  • Location: Turnersville NJ
  • Gender: Male
  • turnersville NJ
    • Share Post
Re: need some help/advice
« Reply #5 on: September 30, 2006, 08:55:41 PM »
I've had that problem.  I oil them up.  Maybe some of that Rust Reaper stuff would work!!  It works well on them.  THen pull the rope a few times until they start springing out again.
108 ARW   NKAWTG...N      Jersey Thunder


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
Need a Little Help/ Advice....

Started by Dewey on Sawmills and Milling

25 Replies
1333 Views
Last post November 26, 2015, 09:43:59 PM
by Dewey
xx
Need advice!

Started by Forestry Man on Sawmills and Milling

10 Replies
1767 Views
Last post July 02, 2011, 07:43:41 AM
by Forestry Man
xx
need some advice

Started by west penn on Drying and Processing

8 Replies
1752 Views
Last post March 31, 2010, 10:21:19 PM
by west penn
xx
Need a little advice

Started by sandhills on Travel Guide

0 Replies
630 Views
Last post May 19, 2016, 07:03:44 PM
by sandhills
 


Powered by EzPortal