The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

FARMA


Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems

Tally-I/O




Author Topic: Hydraulic De-barker motor size?  (Read 766 times)

0 Members and 1 Guest are viewing this topic.

Offline Cutting Edge

  • Senior Member
  • ****
  • Posts: 391
  • Location: WV
  • Gender: Male
    • Share Post
    • Cutting Edge Saw Service, LLC
Hydraulic De-barker motor size?
« on: July 22, 2012, 11:21:17 AM »
Hello All,

I'm trying to figure out what size hyd. motor I need to run a debarker.  The motor will drive an arbor/shaft via v-belt turning a 6" blade.  This will allow it to be geared up or down, so there are more hyd. motor options.  De-barker motor will run off the "Excess Flow" port of the flow control valve.  "Controled Flow" runs the carriage drive/traverse motor.  I'm unsure of required hp, rpm's, etc. requirements to run one properly.

Pump - 6.67 gpm @ 3600 rpms
Carriage hyd. motor - 4.5 cu. in disp./rev. - operates at about "3" on the scale of 1-10 on flow control valve.
De-barker hyd. motor - ???

Thanks in advance
"Winning an argument isn't everything, as long as you are heard and understood" - W.S.


Cutting Edge Saw Service, LLC -
 - Sharpening Services
 - Portable/Custom Milling and Slabbing
 - On-Site Sawmill Maintenance/Repair Services

Factory Direct Kasco WoodMaxx Blades
Ph- (304) 878-3343

Offline Cutting Edge

  • Senior Member
  • ****
  • Posts: 391
  • Location: WV
  • Gender: Male
    • Share Post
    • Cutting Edge Saw Service, LLC
Re: Hydraulic De-barker motor size?
« Reply #1 on: July 22, 2012, 10:32:03 PM »
Maybe a better questions to ask:

What are the specs. (rpm, hp, etc.) for y'alls mills with hyd. motors, or elec., running the de-barker/mudsaw.  Maybe with that information I could work backwards to figure out mine.  :P  Thanks
"Winning an argument isn't everything, as long as you are heard and understood" - W.S.


Cutting Edge Saw Service, LLC -
 - Sharpening Services
 - Portable/Custom Milling and Slabbing
 - On-Site Sawmill Maintenance/Repair Services

Factory Direct Kasco WoodMaxx Blades
Ph- (304) 878-3343


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
Band Wheel Size VS Motor Size?

Started by skocienski on Sawmills and Milling

4 Replies
1067 Views
Last post March 07, 2012, 09:43:25 PM
by pyrocasto
xx
Motor size

Started by furltech on Sawmills and Milling

7 Replies
705 Views
Last post August 04, 2014, 06:19:58 PM
by furltech
xx
Motor size & type

Started by jrokusek on Sawmills and Milling

8 Replies
1905 Views
Last post March 09, 2005, 05:42:25 PM
by Doc
xx
Pulley size for motor

Started by jrokusek on Sawmills and Milling

6 Replies
1626 Views
Last post March 24, 2005, 09:35:46 AM
by jrokusek
 


Powered by EzPortal