iDRY Vacuum Kilns

Sponsors:

New mods for my EZ Boardwalk 40

Started by f350rd, May 19, 2017, 06:09:35 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

f350rd



  

  

  

  

  These are my mods for my EZ boardwalk 40. I have two log turners and a resaw conveyer will get pics later
EZ boardwalk 40 Modified, New Holland lx 865, cat e70b excavator, welding/machine shop, 1999 f350, 2011 f350,72" granberg chainsaw slabbing mill,
48" chainsaw mill

grouch

Find something to do that interests you.

Ianab

Once you have them in your gallery it's easy. Bring up the picture in the gallery, and scroll down a bit.

Find the part that says."To use the above photo in a Forestry Forum post" and below that there is a box with this code in it.
[img]https://forestryforum.com/gallery/albums/userpics/43882/P1010006~1.JPG?easyrotate_cache=1495219733[/img]

Just copy and paste that into your post, and you will get your picture.

Weekend warrior, Peterson JP test pilot, Dolmar 7900 and Stihl MS310 saws and  the usual collection of power tools :)

f350rd

Ianab, thanks for the help. I hope everyone enjoys the pics. The log turners are raised by 1500 lbs. linear actuator that are wireless remote and wireless motor for drives.
EZ boardwalk 40 Modified, New Holland lx 865, cat e70b excavator, welding/machine shop, 1999 f350, 2011 f350,72" granberg chainsaw slabbing mill,
48" chainsaw mill

Ox

I see the linear actuator and winch motor for the log turner.  Are those wheelchair motors for the up/down and feed fwd/rev?
K.I.S.S. - Keep It Simple Stupid
Use it up, wear it out, make it do or do without
1989 GMC 3500 4x4 diesel dump and plow truck, 1964 Oliver 1600 Industrial with Parsons loader and backhoe, 1986 Zetor 5211, Cat's Claw sharpener, single tooth setter, homemade Linn Lumber 1900 style mill, old tools

etroup10

Very nice!! I have the same mill and I'm in the process of doing some of the same mods you did. Already have pineywoods turner/clamp and hydraulic backstops. Just got the motor I'll use for the head up and down. How many rpm is the motor  to raise/lift the head?? Probably going to use a hyd motor for moving the sawhead. Then i will probably do a chain turner and rolker toe boards after that.
NHLA 187th class, lumber inspector. EZ Boardwalk 40 with homemade hydraulics; Gafner Hydraloader; custom built edger, Massey Ferguson 50E, American Sawmill 20" Pony Planer; Husqvarna 55 Rancher

paul case

I believe that I have seen your youtube video etroup. Good job !
https://www.youtube.com/watch?v=pvNTC0L39us

PC
life is too short to be too serious. (some idiot)
2013 LT40SHE25 and Riehl edger,  WM 94 LT40 hd E15. Cut my sawing ''teeth'' on an EZ Boardwalk
sawing oak.hickory,ERC,walnut and almost anything else that shows up.
Don't get phylosophical with me. you will loose me for sure.
pc

f350rd

OX, The drive motor and lift motor are regular gear motors 150/160 rpm they also come in 75/80 rpm. Their around 110.00 each. Everything on the carriage head uses the starting battery. The turners use the aux. battery on the deck.
EZ boardwalk 40 Modified, New Holland lx 865, cat e70b excavator, welding/machine shop, 1999 f350, 2011 f350,72" granberg chainsaw slabbing mill,
48" chainsaw mill

ccronin

Hey F350!  I have an ez boardwalk and I am not to far from you. Would you entertain the idea of showing me your mods in person?  I am in Gwinnett county and would love to visit. 

mroldstyle

where did you get the log turner chain?

Thank You Sponsors!