The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns

Forestry Forum
Sponsored by:

TimberKing Sawmills

Toll Free 1-800-582-0470

LogRite Tools

Norwood Industries Inc.

Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money! sponsored by Northeast STIHL

Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades


Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

Baker Products


iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems

Chainsawr, The Worlds Largest Inventory of Chainsaw Parts

Smith Sawmill Service

Author Topic: Lucas 827 not starting  (Read 2485 times)

0 Members and 1 Guest are viewing this topic.

Offline Runningalucas

  • Senior Member
  • ****
  • Posts: 312
    • Share Post
Lucas 827 not starting
« on: June 06, 2016, 09:14:13 PM »

I've got my mill set up for the Summer.  I did a bad thing according to Lucas, but didn't realize till after the fact.  They state not to jump start your mill, as doing so 'will' mess up the electronics.  My battery which was on a tender through the winter, after charging up tested, 'good', but once in the mill it wouldn't do anything.  I attached another battery via some very long 14 gauge wires that I've got set up with alligator clips for something else.  This resulted in only slightly bumping the engine. 

Knowing it was a bad battery(tested good..tester is from China lol), I bought a new one, cranked the machine over, and still no start.  I used a little ether, and it fired right up.  The machine idled normally, and did so for a number of minutes.  After that, I cranked the machine up to full throttle, and had no problem there; backed it down to an idle, and let it run there for a few more minutes, then shut the machine off.

Next up, after about 20 minutes with farting around with some other stuff, I tried starting it again; no fire.  I used a more ether, and squirted a few times.  It should've fired off even without gas; I'd think?! 

Next up, I pulled both spark plugs, hooked each up to their wires, and held them against the frame, it was bright daylight, but I didn't see a spark. 

Any ideas, or does anyone know where I can find a decent manual online for the Kohler 27?

Thanks In Advance,

Life is short, tragedy is instant, it's what we do with our time in between that matters.  Always strive to do better, to be better.

Offline Runningalucas

  • Senior Member
  • ****
  • Posts: 312
    • Share Post
Re: Lucas 827 not starting
« Reply #1 on: June 07, 2016, 12:44:04 AM »
I got a response from Lucas, I must be getting old, as I forgot about the limit switch on the saw guard.... which was the problem.
Life is short, tragedy is instant, it's what we do with our time in between that matters.  Always strive to do better, to be better.

Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

Lucas gearbox, and LUCAS SLABBER DRIVE HUB pictures wanted

Started by shelbycharger400 on Sawmills and Milling

0 Replies
Last post September 04, 2011, 11:32:02 PM
by shelbycharger400
My Lucas 827

Started by Runningalucas on Lucas Mill

10 Replies
Last post October 25, 2013, 03:59:27 PM
New lucas 6-14

Started by Hiway40frank on Sawmills and Milling

4 Replies
Last post May 19, 2016, 10:17:52 PM
by sigidi
What I did with my new Lucas 830

Started by urbanlumberinc on Sawmills and Milling

8 Replies
Last post November 05, 2006, 10:34:28 PM
by urbanlumberinc

Powered by EzPortal