Text only | Text with Images

The Forestry Forum

General Forestry => Sawmills and Milling => Topic started by: Charles135 on October 23, 2012, 02:29:27 PM

Title: Inserted Tooth Source
Post by: Charles135 on October 23, 2012, 02:29:27 PM
I tried to search the forum, but had no luck.  Does anyone know of a good place to get parts for an inserted tooth head saw?  I have acquired a second blade and it is in need of bits and shanks.  I think it has in it now size "B"
Thanks
Charlie
Title: Re: Inserted Tooth Source
Post by: Jeff on October 23, 2012, 02:31:37 PM
Forum sponsor to the left, Menominee saw.  Give them a call and tell them the forestry forum sent you. :)

(https://forestryforum.com/images/mensaw.gif) (http://www.menomineesaw.com/)
Title: Re: Inserted Tooth Source
Post by: Charles135 on October 23, 2012, 07:42:16 PM
Thanks!
Title: Re: Inserted Tooth Source
Post by: reride82 on October 23, 2012, 08:03:09 PM
I second what Jeff says. I ordered a box anout a month ago and am very pleased with them. Go chrome if you can  ;)
Title: Re: Inserted Tooth Source
Post by: Jeff on October 23, 2012, 08:05:57 PM
I can't agree with chromes. Especially if you hand file.
Title: Re: Inserted Tooth Source
Post by: Charles135 on October 23, 2012, 08:17:08 PM
I was going to ask about the hardened ones.  I use a Andrus Hand sharpener.  I imagine it will take much longer to sharpen the chrome ones. 

Jeff, would it make any difference in your opinion of the Chrome one if I were to purchase the Diamond Wheel they recommend for the carbide teath?
Title: Re: Inserted Tooth Source
Post by: Jeff on October 23, 2012, 08:23:47 PM
Honestly, l have always preferred standard bits due to the ease of bit maintenance. The hardened bits stay sharper longer in clean wood, but the same things that screw up a standard bit will screw up a chrome or destroy a carbide.
Title: Re: Inserted Tooth Source
Post by: Charles135 on October 23, 2012, 08:32:00 PM
Thanks Jeff that make good sense to me!   
Title: Re: Inserted Tooth Source
Post by: Ron Wenrich on October 23, 2012, 08:41:59 PM
You can hand file chrome bits after you knock off the chrome face.  The Andrus won't do it.  You would need some sort of grinder.  After that, you could use the Andrus.  Chrome will cause the file to wear out quicker.
Title: Re: Inserted Tooth Source
Post by: Charles135 on October 23, 2012, 08:45:32 PM
Ron,
this maybe a dumb question; but, if i knock the chrome face off does that not defeat the purpose of the hardened surface?
Title: Re: Inserted Tooth Source
Post by: Ron Wenrich on October 24, 2012, 07:11:01 AM
Your tooth does its cutting by the edges, not the face.  Although there isn't any chrome on the face, you still have chrome on the edge of the teeth.  If you're used to swaging your teeth, you won't be able to do that with chrome.

I went back to all steel teeth for awhile, but the quality of the steel has slipped quite a bit in the past few years, and I couldn't maintain the edge.  It was cost effective for me to go back to the chrome.  The extra cost was made up with a little less downtime in sharpening. 
Title: Re: Inserted Tooth Source
Post by: Charles135 on October 24, 2012, 10:35:29 AM
That too makes since.  Thanks Ron!
Title: Re: Inserted Tooth Source
Post by: Jeff on October 24, 2012, 11:14:05 AM
I quit sawing in late 2005, and was starting to notice the decline in quality of the bits a couple years before that. I'm sure I probably griped about it here somewhere. :D

They have a bunch of knowledgeable people at Menominee. Don't be afraid to ask advice from them on your given situation.
Text only | Text with Images