The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems

Chainsawr, The Worlds Largest Inventory of Chainsaw Parts

Smith Sawmill Service



Author Topic: Kasco WoodMaxx profiles  (Read 2567 times)

0 Members and 1 Guest are viewing this topic.

Offline Sawman815

  • Board Moderator
  • *****
  • Posts: 6
  • Try our Kasco WoodMaxx blades
    • Share Post
    • Kasco
Kasco WoodMaxx profiles
« on: September 22, 2017, 11:25:36 AM »
Kasco WoodMaxx blades come in a variety of widths, thicknesses, and hook angles.
Those include the 10°, 7° and 4° hook angles.

Attached is a .pdf flyer showing the different configurations we currently offer.

Please contact us if you have any questions.

Offline Bluecarpenter22

  • Member*
  • *
  • Posts: 1
  • I'm new!
    • Share Post
Re: Kasco WoodMaxx profiles
« Reply #1 on: December 28, 2020, 10:46:18 AM »
Good morning. Wanting to know about how to go about getting some 144 in Long blades 7/8 spacing in the 10° and I don't know whether to go with 7 or 4° for the hardwood. I've got a 10 horse engine on my Mill would you be able to assist me. Thanks Mark

Offline btulloh

  • Senior Member x2
  • *****
  • Posts: 3940
  • Age: 69
  • Location: Midlothian, VA
  • Gender: Male
  • I never met an air conditioner I didn't like
    • Share Post
Re: Kasco WoodMaxx profiles
« Reply #2 on: December 28, 2020, 11:28:53 AM »
Welcome to the Forestry Forum.  I'm not sure this thread gets checked very often, so I thought I'd try to  help to start.

I use 144" .045 7° Kasco blades on my 9.5 hp mill for most things and they work well for me.  Sounds like the same thing you're looking for.  Kasco retail distribution is handled in the US (eastern?) by Richard at Cutting Edge  @cuttingedge  in WV.  They/he can help you probably.  

The 7° blades work well for me in most everything, but I would probably benefit from 4° for really hard dry oak and similar.  I haven't had the chance to try the 4's, but a lot of people on the forum like them for hard wood and really knotty stuff.  There have been a lot of discussions here on the subject, mainly found in the SAWMILLS and MILLING forum.

Once again, welcome to the FF.

HM126

Offline gmmills

  • Senior Member
  • ****
  • Posts: 332
  • Location: Warren,OH
  • Gender: Male
  • I need to edit my profile!
    • Share Post
Re: Kasco WoodMaxx profiles
« Reply #3 on: December 28, 2020, 09:19:24 PM »
 I buy all my Kasco blades from Cutting Edge. Give him a call, he will give you all the answers you need.  Here is his contact info.  304-878-3343  
                       
Custom sawing full-time since 2000. 
WM LT70D62 Remote with Accuset
Sawing since 1995

Offline Tacotodd

  • Senior Member x2
  • *****
  • Posts: 1555
  • Age: 49
  • Location: Bauxite AR
  • Gender: Male
  • To learn and help
    • Share Post
Re: Kasco WoodMaxx profiles
« Reply #4 on: December 29, 2020, 08:49:06 AM »
@btulloh , if they are anything like I am then those people just have more favorite parts of the forum to check for things to read and/or participate in. For instance:I like the chainsaw part more than anything else but I do read and sometimes participate in other parts. The sawmills and milling parts just don’t hold my attention. But everybody is not the same. OP, you’ll find what you need on FF without a doubt, just keep asking for information and you’ll get good advice!
Trying harder everyday.


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
Kasco WoodMaxx profile

Started by postville on Sawmills and Milling

1 Replies
881 Views
Last post August 19, 2015, 10:38:06 PM
by Cutting Edge
xx
Please Welcome KASCO SharpTech & WoodMaxx Blades!

Started by Jeff on General Board

53 Replies
7673 Views
Last post December 22, 2014, 07:15:25 PM
by Billbob
xx
Your profiles

Started by Jeff on General Board

40 Replies
6560 Views
Last post October 22, 2004, 03:07:02 PM
by Bruce_A
xx
WoodMaxx mill.

Started by hturner12 on Sawmills and Milling

0 Replies
410 Views
Last post August 07, 2018, 10:17:05 AM
by hturner12
 


Powered by EzPortal