The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems

Chainsawr, The Worlds Largest Inventory of Chainsaw Parts

Smith Sawmill Service



Author Topic: Oil Hose Kit Stihl 036  (Read 3639 times)

0 Members and 1 Guest are viewing this topic.

Offline hawkins111

  • member
  • *
  • Posts: 33
  • Location: Bethel Alaska
  • Gender: Male
  • I'm new!
    • Share Post
Oil Hose Kit Stihl 036
« on: August 20, 2014, 08:39:51 PM »
Is there a trick to putting the oil hose kit on a 036? It's the hose that goes from the pump to the bar.

Thank you,

Tom

Offline limbwood

  • Full Member x2
  • ***
  • Posts: 106
  • Age: 60
  • Location: Eastern Iowa
  • Gender: Male
  • I'm new!
    • Share Post
Re: Oil Hose Kit Stihl 036
« Reply #1 on: August 20, 2014, 09:16:39 PM »
I have the best luck cutting a angle on the hose and putting it in from the bar hole first, pull it out aways recut it then fight gitting it on pump, if you warm it a little it helps, but it goes from cold to melted quick so leave it long then pull it back to bar and trim to lenght. good luck

Offline sshier

  • Full Member x2
  • ***
  • Posts: 123
  • Age: 38
  • Location: Lewiston
  • Gender: Male
    • Share Post
Re: Oil Hose Kit Stihl 036
« Reply #2 on: August 20, 2014, 09:20:10 PM »
I'm not positive but I seam to remember feeding the hoes from the bar side through the hole till it seats but I just used small fuel hoes may not be correct but it oils good. Have fun

Offline ZeroJunk

  • Senior Member
  • ****
  • Posts: 738
  • Age: 67
  • Location: Browns Summit N.C.
    • Share Post
Re: Oil Hose Kit Stihl 036
« Reply #3 on: August 21, 2014, 11:42:56 AM »
Keep the piece full length and push/pull through from the bar side. Silicone helps. Heat the end and install on the pump. Pull it through maybe an eighth of an inch farther than it needs to be and cut it off. Then install the pump pulling the line back in to the proper position. Don't forget the spring and where it needs to be to keep the hose from crimping. Mysteriously Stihl didn't give you enough so that you can make two if you mess up.

Offline hawkins111

  • member
  • *
  • Posts: 33
  • Location: Bethel Alaska
  • Gender: Male
  • I'm new!
    • Share Post
Re: Oil Hose Kit Stihl 036
« Reply #4 on: August 21, 2014, 12:08:01 PM »
Yah,

Heat is either just enough or too much. Bunched the first one and now have one on order. I'll keep you guys posted.

Thanks,

Tom

Offline joe_indi

  • Senior Member x2
  • *****
  • Posts: 1341
  • Age: 66
  • Location: India
  • Gender: Male
  • The older I get the more I learn
    • Share Post
Re: Oil Hose Kit Stihl 036
« Reply #5 on: August 23, 2014, 12:27:21 AM »
Tom,
You need to push down  the end of the hose (without the metal bit) through the oil exit hole right at the top. It should come out through a path near the oil pump. The metal fitted end of the hose has to be tapped gently into its seat at the exit hole.
The free end can be heated lightly to slip onto the oil pump. If there is a protection spring fit that on the tube before you fit the end to the pump.

This is the instruction from the 036 workshop manual "Cut new oil delivery hose to a
length of 74 mm and coat the
ends with oil. Use modified flat nose pliers (a = 5,5 mm) to fit the oil delivery hose on the oil pump nipple. Push the oil delivery hose 138RA171 VA through the bore in the bar mounting flange (from the inside outwards) and allow it to project about 10 - 20 mm. If the hose
cannot be pushed through on older machines, drill out the bore to a diameter of 6.2 mm and
deburr carefully. Hold the projecting end with the modified flat nosed pliers. Now push home the sleeve with the modified carburetor screwdriver (R = 1.5 mm). Place oil pump in installed
position. Use modified carburetor screwdriver to push hose into bar mounting flange so that it is recessed about 1-2 mm. Insert oil pump mounting screws and tighten them down firmly"

Hope all that helps

Joe

Offline hawkins111

  • member
  • *
  • Posts: 33
  • Location: Bethel Alaska
  • Gender: Male
  • I'm new!
    • Share Post
Re: Oil Hose Kit Stihl 036
« Reply #6 on: August 27, 2014, 09:47:27 PM »
I got the second kit today. With the education I got on the first one I put my heat gun down and picked up my hair dryer (shop unit). I left the hose full length and pushed it through the front far enough to be able to fit the end on the pump that was removed from it's place. The hair dryer has enough heat to work with without being too hot. You have to get the hose all the way on the pump. Heat the line so that it will push back through the front and form to the curved slot on the case. Now you can cut the hose and heat it to install the brass end. Installing the brass end and pushing the hose back while heating a little will push everything back and keep the end on the pump fully. I did not forget the spring that keeps the hose from collapsing. It goes in before you mess with the brass fitting. I will say, If I had the tool mentioned in the Stihl manual this whole thing would have been much easier. Thanks for all the help. Tom

Offline deerslayer

  • Senior Member
  • ****
  • Posts: 251
  • Age: 2016
  • Location: Georgia
  • Gender: Male
  • old cars, saws, trucks, tractors
    • Share Post
Re: Oil Hose Kit Stihl 036
« Reply #7 on: August 28, 2014, 11:29:27 PM »
I have a disassembled 036 and an oil hose kit in my shop waiting for this treatment. Good info. I've never done one.
Too many chainsaws, not enough wood.
Stihl, Husky, Craftsman, Mac, Homelite, Poulan. Some live here, some just passing through.

Offline AdkStihl

  • Senior Member
  • ****
  • Posts: 723
  • Age: 41
  • Location: North Country NY
  • Gender: Male
    • Share Post
    • J.Miller Photography
Re: Oil Hose Kit Stihl 036
« Reply #8 on: August 29, 2014, 10:27:05 PM »
boil it in a pan of water.
end of story
J.Miller Photography


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
Hydraulic hose

Started by Bruno of NH on Sawmills and Milling

26 Replies
2229 Views
Last post August 10, 2018, 10:18:17 PM
by mike_belben
xx
hydraulic hose

Started by bedway on General Board

3 Replies
968 Views
Last post September 25, 2011, 12:20:07 PM
by maple flats
xx
air hose repair???

Started by shinnlinger on General Board

10 Replies
1782 Views
Last post July 08, 2010, 08:39:39 PM
by nas
xx
Hydraulic hose's.

Started by BargeMonkey on Forestry and Logging

49 Replies
6011 Views
Last post January 25, 2016, 02:31:26 PM
by xalexjx
 


Powered by EzPortal