The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns

Forestry Forum
Sponsored by:

TimberKing Sawmills

Toll Free 1-800-582-0470

LogRite Tools

Norwood Industries Inc.

Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money! sponsored by Northeast STIHL

Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades


Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

Baker Products


iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems

Chainsawr, The Worlds Largest Inventory of Chainsaw Parts

Smith Sawmill Service

Author Topic: 064 oil pump  (Read 410 times)

0 Members and 1 Guest are viewing this topic.

Offline stan064

  • member
  • *
  • Posts: 26
  • Age: 66
  • Location: Midcoast MAINE
  • Gender: Male
  • I'm new!
    • Share Post
064 oil pump
« on: June 06, 2020, 04:48:40 PM »
i need to put new oil pump and nylon gear  on my 064,how do you get the oil line off and new 1 on ,super stiff,been pulling on the line with pliers ,dont want to force it,anything else to look out for,thanks

Offline sablatnic

  • Senior Member
  • ****
  • Posts: 670
  • Location: Denmark
  • Gender: Male
    • Share Post
Re: 064 oil pump
« Reply #1 on: June 07, 2020, 03:14:47 AM »
I normally cut it off, buy a new one, which I heat before I put it on. The nipple in the outlet end I heat too, while pressing it into the line. I use a soldering iron for pressing, which I switch on when I start pressing.
They could easily have made it a bit smarter!!

Offline jrent

  • Member*
  • *
  • Posts: 1
  • I'm new!
    • Share Post
Re: 064 oil pump
« Reply #2 on: July 18, 2020, 12:46:45 PM »
Use a heat gun, but don't get the line to hot as it will collapse.  You can pull it out while limber.  Best to leave in and when you get a oil pump (rare) just reattach. 

Offline thecfarm

  • Senior Member x2
  • *****
  • Posts: 31836
  • Age: 60
  • Location: Chesterville,Maine
  • Gender: Male
  • If I don't do it,it don't get done
    • Share Post
Re: 064 oil pump
« Reply #3 on: July 19, 2020, 06:49:44 AM »
jrent, welcome to the forum. Whatcha got for a saw? or saws  ;D
Model 6020-20hp Manual Thomas bandsaw,TC40A 4wd 40 hp New Holland tractor, 450 Norse Winch, Heatmor 400 OWB,YCC 1978-79

Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

Diesel Primary pump from tank to injector pump

Started by Ironwood on General Board

19 Replies
Last post January 25, 2005, 08:12:11 PM
by Ironwood
New well pump on the way

Started by Sixacresand on General Board

11 Replies
Last post December 10, 2013, 06:06:55 PM
by Sixacresand
Well Pump

Started by Raider Bill on General Board

27 Replies
Last post August 02, 2007, 07:56:15 PM
by Slabs
How big should my pump be?

Started by CX3 on Forestry and Logging

7 Replies
Last post September 25, 2010, 08:28:53 PM
by madmari

Powered by EzPortal