The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems

Chainsawr, The Worlds Largest Inventory of Chainsaw Parts

Smith Sawmill Service



Author Topic: Rust and friction on equipment surface  (Read 1726 times)

0 Members and 1 Guest are viewing this topic.

Offline Don P

  • Senior Member x2
  • *****
  • Posts: 8225
  • Location: Southwestern VA
  • Gender: Male
    • Share Post
    • Calculator Index
Re: Rust and friction on equipment surface
« Reply #20 on: January 16, 2021, 07:49:51 AM »
I get them in the sawmill shop, that is one of the most corrosive substances that can hit steel, and smells nasty too! I've been through several rounds of them, then the owls move in and move them out, then it is clear for awhile and repeats.
The future is a foreign country, they will do things differently there - Simon Winchester

Offline farmfromkansas

  • Senior Member x2
  • *****
  • Posts: 1132
  • Age: 69
  • Location: North central Kansas
  • Gender: Male
    • Share Post
Re: Rust and friction on equipment surface
« Reply #21 on: January 18, 2021, 01:16:52 PM »
Before I put a wood floor in my shop, used to have trouble with rust on CI tables, and got to the point that seemed nothing worked but wipe on poly. That really seals the tops and keeps them from rusting, but has to be replaced if you use the machines a lot.  Since putting down the wood floor, the temp in the shop stays warmer, used 1" treated strips with dow board between the strips, and T&G flooring over the top.  Made a good 10 to 15 degree difference over night. I heat with wood, and don't keep a fire going over night.
Most everything I enjoy doing turns out to be work

Offline Machinebuilder

  • member
  • *
  • Posts: 48
  • Location: Maryville, TN
  • Gender: Male
  • I'm new!
    • Share Post
Re: Rust and friction on equipment surface
« Reply #22 on: March 16, 2021, 10:52:25 AM »
I've switched to Boeshield T9.

It is expensive but dries and doesn't stain wood .

I also use CRC 3-36, it dries a bit gummy. not real good for surfaces that slide.

At work we use Fluid Film to protect machinery when we ship them.
I will probably try some out on my mill.
Dave, Woodmizer LT15, Husqvarna 465 and 435, Bobcat 751, David Brown 770


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
Rust Reaper takes on NZ Sulphur Rust

Started by HSV on General Board

6 Replies
1703 Views
Last post November 06, 2006, 02:46:59 PM
by HSV
xx
Friction wheel

Started by bandmiller2 on Sawmills and Milling

8 Replies
2474 Views
Last post August 01, 2008, 01:17:50 PM
by bandmiller2
xx
Grapple friction shims

Started by jd540b on Forestry and Logging

1 Replies
607 Views
Last post April 02, 2014, 07:37:28 PM
by kiko
xx
TJ friction winch adjustment

Started by mog5858 on Forestry and Logging

3 Replies
1001 Views
Last post February 21, 2013, 07:04:31 PM
by Mark K
 


Powered by EzPortal