iDRY Vacuum Kilns

Sponsors:

Slippery Elm

Started by Slab Slicer, February 03, 2017, 07:22:50 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

Slab Slicer

Just wondering what your thoughts were on Slippery Elm live edge slabs. Sliced up quite a bit into 2+ inch slabs. Lots of character with the crotch areas.
2016 LT35HDG25, Kubota L2501 w/ FEL, Kubota BX1500 w/FEL and custom skidding rig, Stihl MS 500i, Stihl MS362-25", Stihl MS250-20", Stihl MS192-18",  2001 F250 SD 7.3, GMC Sierra Dually 6.0 gasser, Peaqua 16" 10K trailer, Sur-Trac 12' Dump Trailer 10K
Chuck

WDH

Very pretty.  Has spiral grain so prone to twist and warp.  Best slabs will be quartersawn.  First flatsawn slabs off the log usually move a lot and are a challenge to dry flat.
Woodmizer LT40HDD35, John Deere 2155, Kubota M5-111, Kubota L2501, Nyle L53 Dehumidification Kiln, and a passion for all things with leafs, twigs, and bark.  hamsleyhardwood.com

Slab Slicer

Thanks WDH. All is stacked and snickered of course, but I added 4 or 5 ratchet straps around each flitch, in an attempt to keep everything flat. I go through all the stacks, and tighten them down every now and then, to account for shrinkage. Might be a waste of time. Only time will tell......Or has this already been tried, and failed?
2016 LT35HDG25, Kubota L2501 w/ FEL, Kubota BX1500 w/FEL and custom skidding rig, Stihl MS 500i, Stihl MS362-25", Stihl MS250-20", Stihl MS192-18",  2001 F250 SD 7.3, GMC Sierra Dually 6.0 gasser, Peaqua 16" 10K trailer, Sur-Trac 12' Dump Trailer 10K
Chuck

Slab Slicer

STICKERED!!!!! Stupid auto correct phone
2016 LT35HDG25, Kubota L2501 w/ FEL, Kubota BX1500 w/FEL and custom skidding rig, Stihl MS 500i, Stihl MS362-25", Stihl MS250-20", Stihl MS192-18",  2001 F250 SD 7.3, GMC Sierra Dually 6.0 gasser, Peaqua 16" 10K trailer, Sur-Trac 12' Dump Trailer 10K
Chuck

WDH

What you have done should help if you keep the straps tight. 
Woodmizer LT40HDD35, John Deere 2155, Kubota M5-111, Kubota L2501, Nyle L53 Dehumidification Kiln, and a passion for all things with leafs, twigs, and bark.  hamsleyhardwood.com

Den Socling

I thought snickered was funny.  :D

WDH

The spiral grain woods snicker back at you  :D.
Woodmizer LT40HDD35, John Deere 2155, Kubota M5-111, Kubota L2501, Nyle L53 Dehumidification Kiln, and a passion for all things with leafs, twigs, and bark.  hamsleyhardwood.com

thecfarm

My auto brain did not even catch the snicker.
Model 6020-20hp Manual Thomas bandsaw,TC40A 4wd 40 hp New Holland tractor, 450 Norse Winch, Heatmor 400 OWB,YCC 1978-79

Slab Slicer

2016 LT35HDG25, Kubota L2501 w/ FEL, Kubota BX1500 w/FEL and custom skidding rig, Stihl MS 500i, Stihl MS362-25", Stihl MS250-20", Stihl MS192-18",  2001 F250 SD 7.3, GMC Sierra Dually 6.0 gasser, Peaqua 16" 10K trailer, Sur-Trac 12' Dump Trailer 10K
Chuck

Slab Slicer

2016 LT35HDG25, Kubota L2501 w/ FEL, Kubota BX1500 w/FEL and custom skidding rig, Stihl MS 500i, Stihl MS362-25", Stihl MS250-20", Stihl MS192-18",  2001 F250 SD 7.3, GMC Sierra Dually 6.0 gasser, Peaqua 16" 10K trailer, Sur-Trac 12' Dump Trailer 10K
Chuck

fishpharmer

Wow!  I sure like the looks of that grain. 8)
Built my own band mill with the help of Forestry Forum. 
Lucas 618 with 50" slabber
WoodmizerLT-40 Super Hydraulic
Deere 5065E mfwd w/553 loader

The reason a lot of people do not recognize opportunity is because it usually goes around wearing overalls looking like hard work. --Tom A. Edison

Don P

I do like red elm, wish there was more of it around here.

Slab Slicer

This slippery elm smells bad when you mill it, but the grain is too nice to not mill it.
2016 LT35HDG25, Kubota L2501 w/ FEL, Kubota BX1500 w/FEL and custom skidding rig, Stihl MS 500i, Stihl MS362-25", Stihl MS250-20", Stihl MS192-18",  2001 F250 SD 7.3, GMC Sierra Dually 6.0 gasser, Peaqua 16" 10K trailer, Sur-Trac 12' Dump Trailer 10K
Chuck

Thank You Sponsors!