iDRY Vacuum Kilns

Sponsors:

Making some T&G

Started by metalspinner, May 06, 2021, 03:01:43 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

Print
Go Down Pages1 2 All
User actions

metalspinner

May 06, 2021, 03:01:43 PM
I took a couple of loads, about 1200bf, of mixed hardwood out to Jacob's to run through his moulder. 
This is mostly red and white oak along with elm, hickory, maple, and sycamore. 
I will use this in my workshop as wall paneling in the bench room. 

https://youtu.be/hneJjbh0esQ



 



 

It's always nice to see the aged, weathered boards turn to a beautiful stack of finished lumber.  8)
I do what the little voices in my wife's head tell me to do.

alan gage

#1
May 06, 2021, 04:02:14 PM
Quote from: metalspinner on May 06, 2021, 03:01:43 PM
I took a couple of loads, about 1200bf, of mixed hardwood out to Jacob's to run through his moulder.
This is mostly red and white oak along with elm, hickory, maple, and sycamore.
I will use this in my workshop as wall paneling in the bench room.

https://youtu.be/hneJjbh0esQ



 



 

It's always nice to see the aged, weathered boards turn to a beautiful stack of finished lumber.  8)
That's great. Good looking stuff!
I recently did the same thing in my shop but I must have done something wrong because there was a lot more time involved and an extra few dozen steps in the process. :)
Alan
Timberking B-16, a few chainsaws from small to large, and a Bobcat 873 Skidloader.

Brad_bb

#2
May 06, 2021, 07:08:45 PM
Cool!  Is that second operation belt sanding on one side?
Anything someone can design, I can sure figure out how to fix!
If I say it\\\\\\\'s going to take so long, multiply that by at least 3!

metalspinner

#3
May 06, 2021, 07:56:08 PM
Bradd_bb
Yes that's a belt sander. Not sure what grit it was, though?

Something not shown was everything went through an edger before the moulder. 
I do what the little voices in my wife's head tell me to do.

Trackerbuddy

#4
May 06, 2021, 08:44:56 PM
Quote from: metalspinner on May 06, 2021, 07:56:08 PM
Bradd_bb
Yes that's a belt sander. Not sure what grit it was, though?

Something not shown was everything went through an edger before the moulder.
Does all wood need to be edged before the molder? Or does it depend on the machine?

metalspinner

#5
May 06, 2021, 09:18:37 PM
It definitely needed to go through the edger.  I ended up with three different widths. 3 1/2, 5, and 7 inches. 
Those scraggly looking boards looked really good after the edger. I think they would have been just as nice on the wall as the T&G. 

This ended up being about being about 1 1/2 of my stacks. Not that that is an official unit of measure! :laugh: 


 
I do what the little voices in my wife's head tell me to do.

metalspinner

#6
August 01, 2021, 06:34:33 PM
After three coats of poly, the paneling done. 




 

 

This is all basically log-run, urban hardwoods. I kept lots of "character boards" in the mix. These are good conversation starters for visitors. 

A chainsaw pruning on a red oak tree...




Spalted beech...
  

 

Spalted, quarter-sawn Sycamore...





Bullets in red oak...



 


Service panel access door...

 

 
I do what the little voices in my wife's head tell me to do.

Southside

#7
August 01, 2021, 06:39:19 PM
Beautiful job!!  
Franklin buncher and skidder
JD Processor
Woodmizer LT Super 70 and LT35 sawmill, KD250 kiln, BMS 250 sharpener and setter
Riehl Edger
Woodmaster 725 and 4000 planner and moulder
Enough cows to ensure there is no spare time.
White Oak Meadows

trimguy

#8
August 01, 2021, 08:01:48 PM
Wow ! That's great .

Crossroads

#9
August 01, 2021, 11:58:13 PM
Very nice!
With the right fulcrum and enough leverage, you can move the world!

2017 LT40 wide, BMS250 and BMT250,036 stihl, 2001 Dodge 3500 5.9 Cummins, l8000 Ford dump truck, hr16 Terex excavator, Valley je 2x24 edger, Gehl ctl65 skid steer, JD350c dozer

customsawyer

#10
August 02, 2021, 06:37:51 AM
Nothing wrong with that.
Two LT70s, Nyle L200 kiln, 4 head Pinheiro planer, 30" double surface Cantek planer, Lucas dedicated slabber, Slabmizer, and enough rolling stock and chainsaws to keep it all running.
www.thecustomsawyer.com

scsmith42

#11
August 02, 2021, 06:43:43 AM
Well done sir!
Peterson 10" WPF with 65' of track
Smith - Gallagher dedicated slabber
Tom's 3638D Baker band mill
and a mix of log handling heavy equipment.

bannerd

#12
August 02, 2021, 11:47:21 AM
Sure beats a router doing it by hand!!  Gorgeous!

Crossroads

#13
August 02, 2021, 07:46:28 PM
I just realized you t&g is a square joint without the V- groove. It looks great, thanks for sharing 
With the right fulcrum and enough leverage, you can move the world!

2017 LT40 wide, BMS250 and BMT250,036 stihl, 2001 Dodge 3500 5.9 Cummins, l8000 Ford dump truck, hr16 Terex excavator, Valley je 2x24 edger, Gehl ctl65 skid steer, JD350c dozer

Bruno of NH

#14
August 03, 2021, 07:31:28 AM
A job well done
Lt 40 wide with 38hp gas and command controls , F350 4x4 dump and lot of contracting tools

WDH

#15
August 03, 2021, 07:36:43 PM
I love it. 
Woodmizer LT40HDD35, John Deere 2155, Kubota M5-111, Kubota L2501, Nyle L53 Dehumidification Kiln, and a passion for all things with leafs, twigs, and bark.  hamsleyhardwood.com

metalspinner

#16
August 03, 2021, 10:44:39 PM
I have been asked repeatedly by everyone that has ever visited my house, "What are you going to do with all that wood?!?"

"I'm going to use it in my shop some day!" I always replied. :D :D

Well, this is just about 1 1/2 stacks of my stash. Now I'm asking myself, "what are you going to do with all this wood?!?"
I do what the little voices in my wife's head tell me to do.

WDH

#17
August 04, 2021, 08:31:00 AM
I can't help you with that problem  ;D.
Woodmizer LT40HDD35, John Deere 2155, Kubota M5-111, Kubota L2501, Nyle L53 Dehumidification Kiln, and a passion for all things with leafs, twigs, and bark.  hamsleyhardwood.com

Peter Drouin

#18
August 04, 2021, 12:29:04 PM
 smiley_clapping
Very nice.
A&P saw Mill LLC.
45' of Wood Mizer, cutting since 1987.
License NH softwood grader.

att_t_2d

#19
August 05, 2021, 06:45:49 AM
How thick is the paneling?

metalspinner

#20
August 05, 2021, 01:52:40 PM
I didn't put a tape measure to it. My guess is a strong 3/4. Maybe 13/16. I'll measure in a little while. 
Random widths 4, 6, and 8 rough lumber.  
I do what the little voices in my wife's head tell me to do.

Stephen1

#21
August 05, 2021, 10:50:54 PM
That looks great!
IDRY Vacum Kiln, LT40HDWide, BMS250 sharpener/setter 742b Bobcat, TCM forklift, Sthil 026,038, 461. 1952 TEA Fergusan Tractor

teakwood

#22
August 06, 2021, 08:25:11 AM
that's awesome work! nicely done

how did you fix the paneling to the wall? have a video or fotos?
National Stihl Timbersports Champion Costa Rica 2018

barbender

#23
August 06, 2021, 10:27:38 AM
Looks great!!
Too many irons in the fire

metalspinner

#24
August 06, 2021, 01:08:39 PM
Teakwood,
I toenailed them through the tongue right into the studs with a finish nailer. 
I do what the little voices in my wife's head tell me to do.
Print
Go Up Pages1 2 All
User actions

Thank You Sponsors!