iDRY Vacuum Kilns

Sponsors:

quartersawn red oak bed project

Started by Dan_Shade, January 09, 2011, 07:09:20 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

SwampDonkey

Dan, Looks like a good article. I'm snagging the PDF file now.  :)
"No amount of belief makes something a fact." James Randi

1 Thessalonians 5:21

2020 Polaris Ranger 570 to forward firewood, Husqvarna 555 XT Pro, Stihl FS560 clearing saw and continuously thinning my ground, on the side. Grow them trees. (((o)))

Dodgy Loner

Quote from: Dan_Shade on January 25, 2011, 08:06:20 PM
so arts and crafts design doesn't incorporate raised panels?

I can't say that there wasn't any Arts and Crafts furniture built with raised panels, but certainly the furniture that came to define the style was built with flat panels - usually just a 1/4" thick board in a 1/4" groove. A lot of Shaker furniture is built the same way. I am partial to that technique, because it allows me to resaw a 4/4 board into two bookmatched panels. A thicker panel in a bed is probably a good idea, given the abuse that it's liable to receive ;)
"There is hardly anything in the world that some man cannot make a little worse and sell a little cheaper, and the people who consider price only are this man's lawful prey." -John Ruskin

Any idiot can write a woodworking blog. Here's mine.

isawlogs

Have you looked at BusyBee Tools  SD , they have a mortise attachment and drill press for those of us that are fanancialy at times chalenged  ;D
A man does not always grow wise as he grows old , but he always grows old as he grows wise .

   Marcel

Wrangler55

Quote from: isawlogs on January 26, 2011, 07:54:42 AM
Have you looked at BusyBee Tools  SD , they have a mortise attachment and drill press for those of us that are fanancialy at times chalenged  ;D

I make a jig to match the tenion I'm making a mortise for, then drill out most of the waste with a forsner bit, then I use a pattern bit in my plunge router to follow the template and a chisel to square up the corners.  Last I split the tenion on a table saw, and use a wedge to assemble the joint. After sanding flush, they look and feel perfect without a lot of effort.

Hal
I'm so covered with sawdust, my nickname should be dusty...

SwampDonkey

Marcel, they are not very expensive to begin with. Around $110 from Lee's and Canadian Tire sells a Master Craft that would be warranted if it broke, probably cheaper. I have heard various reports using these things, many are not really satisfied especially with the harder woods. They say not to force the work, sounds like it can be slow, but probably no slower than hand chiseled. You just have to watch what brand of press you get to be sure it can be attached. I would much prefer a mortising machine. ;D
"No amount of belief makes something a fact." James Randi

1 Thessalonians 5:21

2020 Polaris Ranger 570 to forward firewood, Husqvarna 555 XT Pro, Stihl FS560 clearing saw and continuously thinning my ground, on the side. Grow them trees. (((o)))

SwampDonkey

"No amount of belief makes something a fact." James Randi

1 Thessalonians 5:21

2020 Polaris Ranger 570 to forward firewood, Husqvarna 555 XT Pro, Stihl FS560 clearing saw and continuously thinning my ground, on the side. Grow them trees. (((o)))

SwampDonkey

I've moved this post over to my cabinetry thread. ;)
"No amount of belief makes something a fact." James Randi

1 Thessalonians 5:21

2020 Polaris Ranger 570 to forward firewood, Husqvarna 555 XT Pro, Stihl FS560 clearing saw and continuously thinning my ground, on the side. Grow them trees. (((o)))

Thank You Sponsors!