- Welcome to The Forestry Forum.
How are things going?
958 Guests, 16 Users
Magicman, archeryplus, Al_Smith, Merlin, barbender, bluegrasspicker, beenthere, stihltoomany, B.C.C. Lapp, ihookem, Nobohdy, Dan_Shade, blackhawk, Jeff, TimW, Old Greenhorn
Magicman, archeryplus, Al_Smith, Merlin, barbender, bluegrasspicker, beenthere, stihltoomany, B.C.C. Lapp, ihookem, Nobohdy, Dan_Shade, blackhawk, Jeff, TimW, Old Greenhorn
Recent posts
#1
Forestry and Logging / Re: Maintaining the state park...
Last post by barbender - Today at 01:05:38 PMAndries, relating the proper size of Ash pole to a hockey stick is very Canadian of you😂
#2
Sawmills and Milling / Re: OldJarheads Milling Thread...
Last post by OlJarhead - Today at 12:32:48 PMThanks
1. Yes I disconnected the wires to test for continuity.
2. Battery voltage starts around 12.65 off the solar panel and drops to around 12.5 or so.
3. Battery voltage at 11.9-12.x (low) was after starting the engine without the alternator working.
4. When alternator is working (now) the voltage at battery shows 14.79v which is inline with what WM tells me there should be.
The battery is old so it may need to be replaced but at least now, the alternor is charging.
On the light, I agree. It should come on until the alternator starts to charge then go out so that's a little strange and needs further testing.
Cheers!
1. Yes I disconnected the wires to test for continuity.
2. Battery voltage starts around 12.65 off the solar panel and drops to around 12.5 or so.
3. Battery voltage at 11.9-12.x (low) was after starting the engine without the alternator working.
4. When alternator is working (now) the voltage at battery shows 14.79v which is inline with what WM tells me there should be.
The battery is old so it may need to be replaced but at least now, the alternor is charging.
On the light, I agree. It should come on until the alternator starts to charge then go out so that's a little strange and needs further testing.
Cheers!
#3
Sawmills and Milling / Re: board edger for dried lumb...
Last post by scsmith42 - Today at 12:26:23 PMI use a 15hp Woodmizer twin blade edger to edge dry lumber into flooring blanks for the moulder. It does a fine job.
#4
The Outdoor Board / Re: Coyote takes a dirt nap
Last post by JD Guy - Today at 12:11:56 PMWell, I don't believe there's a coyote season here but if they're harassing my wife's chickens they die 
#5
Sawmills and Milling / Re: Did something dumb today.
Last post by GAB - Today at 12:03:33 PMQuote from: firefighter ontheside on Today at 10:37:49 AMTom, that's just bad luck. What are the odds?With his luck, or lack there of, the odds are pretty good.
GAB
#6
Sawmills and Milling / Re: Sawing Project 2024
Last post by stanwelch - Today at 12:01:18 PMAnother GREAT project. 
Thank you Nathan and Robert for the excellent videos and Jake —
You are a great host. Thanks for allowing us to invade your space for a little while
Shout out to Jeff for the Forum that has given us the opportunity to meet and share with friends
Stan
Thank you Nathan and Robert for the excellent videos and Jake —You are a great host. Thanks for allowing us to invade your space for a little while
Shout out to Jeff for the Forum that has given us the opportunity to meet and share with friends
Stan
#7
General Board / Re: It's a Go! 2024 FF Pigroa...
Last post by Ed_K - Today at 11:38:06 AM Rita an I are booked . Staying at Days Inn in Mt Pleasant. Will need some directions to Jeff an Tammy's.
. Staying at Days Inn in Mt Pleasant. Will need some directions to Jeff an Tammy's. #8
General Board / Re: Help with a dig pattern.
Last post by SwampDonkey - Today at 11:16:48 AMRhubarb is above ground here, but it is still early for some stuff. Only wild flower out yet here is colts foot, which has been out since March.
#9
General Board / Re: Help with a dig pattern.
Last post by thecfarm - Today at 10:58:02 AMI have not look at my hostas, but doubt they are up yet.
Them things will spread too. If the deer don't kill them back.
Them things will spread too. If the deer don't kill them back.
#10
General Woodworking / Re: Watcha Makin'?
Last post by firefighter ontheside - Today at 10:43:54 AMMaybe a more flexible epoxy like G flex will be better.
Here is the case for dad. I will finish it the next time I work on it and give it to mom.
Here is the case for dad. I will finish it the next time I work on it and give it to mom.
