The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems

Chainsawr, The Worlds Largest Inventory of Chainsaw Parts

Smith Sawmill Service



Author Topic: Building a deck  (Read 4607 times)

0 Members and 1 Guest are viewing this topic.

Offline Don P

  • Senior Member x2
  • *****
  • Posts: 8750
  • Location: Southwestern VA
  • Gender: Male
    • Share Post
    • Calculator Index
Re: Building a deck
« Reply #20 on: April 20, 2007, 11:10:49 PM »
Who was it that was talking about their taxed footage increasing. The shrubbery grew and increased the taped perimeter  ::).
We had one assessor come to a job, I thought he was an appraiser from the bank not the county. I was touring him through pointing out value and extra's, really trying to help with what I presumed to be a homeowners tight situation. Oooops   :-X.

I still attach to and flash against the house. We use treated rims where decks will go and flash against the rim and under the ledger with a z type bend under the ledger. Another flashing goes above the ledger with a z bend over the top edge onto the face about 1/2". The two flashes shingle lap each other on the wall.
The future is a foreign country, they will do things differently there - Simon Winchester

Offline DanG

  • Senior Member x2
  • *****
  • Posts: 13512
  • Age: 75
  • Location: Chattahoochee, Florida USA
  • Gender: Male
  • DanG, The Official ForestryForum Cussword
    • Share Post
Re: Building a deck
« Reply #21 on: April 20, 2007, 11:44:14 PM »
One good reason to fasten the deck to the house is lateral stability.  If it is secured to the house, it ain't gonna wobble.  Wobbles cause weakness, and weakness causes lawsuits.  You can still make it stable without adjoining it, but it takes a whole lot more bracing.

The plans for my house call for a ledger board bolted through the poured lentil with inch bolts.  I'm gonna go them one better and install a pier at each support point.  It is a covered porch, so I won't likely have any water woes, but I'll feel better knowing it is supported better than it has to be.

Definition:

Built to code:  Built as poorly as the law will allow.
"I don't feel like an old man.  I feel like a young man who has something wrong with him."  Dick Cavett
"Beat not thy sword into a plowshare, rather beat the sword of thine enemy into a plowshare."

Offline Norm

  • Senior Member x2
  • *****
  • Posts: 7653
  • Age: 65
  • Gender: Male
    • Share Post
Re: Building a deck
« Reply #22 on: April 22, 2007, 08:18:07 AM »
That reminds me when we built our last house. I came pulling up and there sat the county assesors car. He was right in the middle of the framing crew with a tape measure. I walked up and asked him what he was up to. Seems he didn't think the blueprints we provided were accurate enought and besides some people change things just to fool them. I asked if he had his insurance rider with him to be on our job. He looked puzzled as I escorted him off the frame and told him not to come back until he had one. :D


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

question
Need Advice on building Deck over Trailer

Started by PawNature on General Board

8 Replies
8323 Views
Last post June 12, 2006, 04:45:13 PM
by Weekend_Sawyer
xx
Time to re deck the deck

Started by rimshot on Sawmills and Milling

6 Replies
1314 Views
Last post October 01, 2013, 06:43:41 PM
by rimshot
xx
Oak Deck

Started by campy on Sawmills and Milling

19 Replies
17965 Views
Last post January 22, 2010, 06:53:19 AM
by ljmathias
xx
The Deck (s)

Started by hawby on General Board

7 Replies
1642 Views
Last post June 18, 2003, 06:48:17 PM
by Jeff
 


Powered by EzPortal