The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems

Chainsawr, The Worlds Largest Inventory of Chainsaw Parts

Smith Sawmill Service



Author Topic: g matic  (Read 550 times)

0 Members and 1 Guest are viewing this topic.

Offline coxy

  • Senior Member x2
  • *****
  • Posts: 6283
  • Age: 51
  • Location: eastern n.y
  • Gender: Male
    • Share Post
g matic
« on: July 17, 2017, 12:38:32 PM »
what do you guys use to put under the puller point to take the out side bearing off so you don't mess the inside of the hole up where the little u cup goes

Offline North River Energy

  • Senior Member
  • ****
  • Posts: 846
  • Age: 54
  • Location: ME/NH
  • Gender: Male
    • Share Post
Re: g matic
« Reply #1 on: July 17, 2017, 12:45:33 PM »
Have not had to do that particular repair yet, but would probably turn up some sort of 'push pad' on the lathe.
With a 'stud' to keep it centered in the critical hole, and a small pocket on the opposite side to center the puller screw.

Offline Ed_K

  • Senior Member x2
  • *****
  • Posts: 3549
  • Age: 68
  • Location: Leyden,Ma.
  • Gender: Male
  • Leave it better than you found it. Ed_K
    • Share Post
Re: g matic
« Reply #2 on: July 17, 2017, 02:40:30 PM »
 I used a chisel behind it and just tapped on it till it came loose.
Ed K

Offline coxy

  • Senior Member x2
  • *****
  • Posts: 6283
  • Age: 51
  • Location: eastern n.y
  • Gender: Male
    • Share Post
Re: g matic
« Reply #3 on: July 17, 2017, 02:55:46 PM »
I use a flat plate mostly but didn't know if any one had a better rig


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
g matic 119

Started by coxy on Forestry and Logging

4 Replies
647 Views
Last post May 09, 2018, 02:24:04 PM
by coxy
xx
gear matic 19/119

Started by coxy on Forestry and Logging

23 Replies
3461 Views
Last post May 12, 2016, 12:15:00 AM
by John Woodworth
xx
help with a gear matic 19

Started by Brian w on Forestry and Logging

15 Replies
1471 Views
Last post February 11, 2019, 03:18:49 PM
by mike_belben
xx
gear-o-matic 8A need to be rebuilt

Started by Ken@MN on Forestry and Logging

3 Replies
759 Views
Last post October 14, 2013, 09:07:17 PM
by rfm7fxfox
 


Powered by EzPortal