The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems

Chainsawr, The Worlds Largest Inventory of Chainsaw Parts

Smith Sawmill Service



Author Topic: Cooking Pavilion  (Read 13067 times)

0 Members and 1 Guest are viewing this topic.

Offline Mooseherder

  • Administrator
  • *****
  • Posts: 9488
  • Age: 61
  • Location: Mainely Fl.
  • Gender: Male
    • Share Post
Re: Cooking Pavilion
« Reply #60 on: January 16, 2012, 05:38:55 PM »
Thanks Guys! :)
Here is the finished picture except for some more stain and the center table and the Pizza oven. :D
I bought some steel bars with predrilled holes just in case for the Drum Chicken.
They are a nice fit across the top of the inner brick.
I'll have to come up with some fabrication for a top.
I'm also pondering making the Oven work off of propane and or Wood Coals.
How hard is it to make a safe rig that I could drill pipe for this and then buy some propane fittings?

 

 
Lane Circle Mill
Homemade Bandmill

Offline LeeB

  • Senior Member x2
  • *****
  • Posts: 8383
  • Age: 61
  • Location: Yellville Arkansas
  • Gender: Male
  • proud to be a TEXAN in Arkansas
    • Share Post
Re: Cooking Pavilion
« Reply #61 on: January 17, 2012, 08:23:50 AM »
Can you weld? Use square tube. Cap the ends, drill and tap the holes for the burner fittings(I have used grease zerts with the ball knocked out for flame outlets) and a low pressure regulator, or just gut an old propane oven. You can get them for next to nothing.
'98 LT40HDD/Lombardini, Case 580L, Cat D4C, JD 3032 tractor, JD 5410 tractor, Husky 346, 372 and 562XP's. Stihl MS180 and MS361, 1998 and 2006 3/4 Ton 5.9 Cummins 4x4's, 1989 Dodge D100 w/ 318, and a 1966 Chevy C60 w/ dump bed.

Offline Norm

  • Senior Member x2
  • *****
  • Posts: 7653
  • Age: 65
  • Gender: Male
    • Share Post
Re: Cooking Pavilion
« Reply #62 on: January 17, 2012, 09:25:52 AM »
I'd go with Lee's recommendation on finding an old gas grill. Craigslist should get you lots of hits for some.

Offline Mooseherder

  • Administrator
  • *****
  • Posts: 9488
  • Age: 61
  • Location: Mainely Fl.
  • Gender: Male
    • Share Post
Re: Cooking Pavilion
« Reply #63 on: January 17, 2012, 09:43:38 AM »
I have never welded but my brothers are real good at it.
I've asked them to show me how to weld.
The problem is they're 2 thousand miles away. 
There is a guy with a sign in his front yard around here that says welding so maybe I'll check with him.
I have my Mother's old Gas stove in storage for use in my Northern Cook Shack but wil be keeping that one intact.  It is at least 50 years old because my parents bought that house when I was tree. ;D
Lane Circle Mill
Homemade Bandmill

Offline Raider Bill

  • Senior Member x2
  • *****
  • Posts: 7957
  • Location: The Sun Coast
  • Gender: Male
  • Who will pull the wagon when everyone rides?
    • Share Post
Re: Cooking Pavilion
« Reply #64 on: January 17, 2012, 09:45:53 AM »
What kind of tree were you? ;D
The First 60 some years of childhood is always the hardest.

Offline Mooseherder

  • Administrator
  • *****
  • Posts: 9488
  • Age: 61
  • Location: Mainely Fl.
  • Gender: Male
    • Share Post
Re: Cooking Pavilion
« Reply #65 on: January 17, 2012, 09:58:03 AM »
A stump. :D
Lane Circle Mill
Homemade Bandmill

Offline LeeB

  • Senior Member x2
  • *****
  • Posts: 8383
  • Age: 61
  • Location: Yellville Arkansas
  • Gender: Male
  • proud to be a TEXAN in Arkansas
    • Share Post
Re: Cooking Pavilion
« Reply #66 on: January 17, 2012, 10:02:28 AM »
The old gas grill would likely be cheaper and easier.
'98 LT40HDD/Lombardini, Case 580L, Cat D4C, JD 3032 tractor, JD 5410 tractor, Husky 346, 372 and 562XP's. Stihl MS180 and MS361, 1998 and 2006 3/4 Ton 5.9 Cummins 4x4's, 1989 Dodge D100 w/ 318, and a 1966 Chevy C60 w/ dump bed.

Offline Mooseherder

  • Administrator
  • *****
  • Posts: 9488
  • Age: 61
  • Location: Mainely Fl.
  • Gender: Male
    • Share Post
Re: Cooking Pavilion
« Reply #67 on: January 17, 2012, 10:07:27 AM »
I might go with new replacement parts from one of the depots.
What would I need in between the tank and the burner besides a regulator?
Lane Circle Mill
Homemade Bandmill

Offline Raider Bill

  • Senior Member x2
  • *****
  • Posts: 7957
  • Location: The Sun Coast
  • Gender: Male
  • Who will pull the wagon when everyone rides?
    • Share Post
Re: Cooking Pavilion
« Reply #68 on: January 17, 2012, 10:09:00 AM »
The old gas grill would likely be cheaper and easier.

The problem with them is normally the burners are rusted out. I used new SS replacement parts.
The First 60 some years of childhood is always the hardest.

Offline Mooseherder

  • Administrator
  • *****
  • Posts: 9488
  • Age: 61
  • Location: Mainely Fl.
  • Gender: Male
    • Share Post
Re: Cooking Pavilion
« Reply #69 on: January 17, 2012, 10:14:40 AM »
Oh, and bricks flying in every direction from a blowout is my main concern. ::)
Lane Circle Mill
Homemade Bandmill

Offline LeeB

  • Senior Member x2
  • *****
  • Posts: 8383
  • Age: 61
  • Location: Yellville Arkansas
  • Gender: Male
  • proud to be a TEXAN in Arkansas
    • Share Post
Re: Cooking Pavilion
« Reply #70 on: January 17, 2012, 10:39:38 AM »
I would use 1/2" black pipe. Are there any vent holes down at the bottom to keep any gas from accumulating? I shouldn't think it would be any more concern than lighting an oven. I use a high pressure ball valve on my fryer to keep the gas off till I'm ready to light it in addition to the valve on the bottle. I also use it to regulate the flame, much the same as a burner control. The whole thing is home made and probably would get me thrown in jail. It will boil 5 gal of water in just a few minutes. Sounds like a jet engine. Used a grease zert for the tip and have a piece of flat iron right above it for a target to spread out the flame. Been using it for 15 years or more.
'98 LT40HDD/Lombardini, Case 580L, Cat D4C, JD 3032 tractor, JD 5410 tractor, Husky 346, 372 and 562XP's. Stihl MS180 and MS361, 1998 and 2006 3/4 Ton 5.9 Cummins 4x4's, 1989 Dodge D100 w/ 318, and a 1966 Chevy C60 w/ dump bed.

Offline Tdawg

  • member
  • *
  • Posts: 44
  • Age: 58
  • Location: Oro Medonte, Ontario
  • Gender: Male
    • Share Post
Re: Cooking Pavilion
« Reply #71 on: January 17, 2012, 07:57:04 PM »
I would use 1/2" black pipe. Are there any vent holes down at the bottom to keep any gas from accumulating? I shouldn't think it would be any more concern than lighting an oven. I use a high pressure ball valve on my fryer to keep the gas off till I'm ready to light it in addition to the valve on the bottle. I also use it to regulate the flame, much the same as a burner control. The whole thing is home made and probably would get me thrown in jail. It will boil 5 gal of water in just a few minutes. Sounds like a jet engine. Used a grease zert for the tip and have a piece of flat iron right above it for a target to spread out the flame. Been using it for 15 years or more.

Do you have any pics? Or would you prefer to keep them from the authorities? :D :D :D

Offline LeeB

  • Senior Member x2
  • *****
  • Posts: 8383
  • Age: 61
  • Location: Yellville Arkansas
  • Gender: Male
  • proud to be a TEXAN in Arkansas
    • Share Post
Re: Cooking Pavilion
« Reply #72 on: January 17, 2012, 08:07:40 PM »
I'll take some pics when I get back home. I'm half way around the world from it right now.
'98 LT40HDD/Lombardini, Case 580L, Cat D4C, JD 3032 tractor, JD 5410 tractor, Husky 346, 372 and 562XP's. Stihl MS180 and MS361, 1998 and 2006 3/4 Ton 5.9 Cummins 4x4's, 1989 Dodge D100 w/ 318, and a 1966 Chevy C60 w/ dump bed.


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
Pavilion in FL

Started by MishaZ on Timber Framing/Log construction

11 Replies
780 Views
Last post December 29, 2020, 06:54:40 AM
by kantuckid
question
HP Pavilion

Started by bedway on General Board

11 Replies
543 Views
Last post March 29, 2020, 01:27:55 AM
by Ianab
xx
Another pavilion build?

Started by Jeff on Timber Framing/Log construction

6 Replies
177 Views
Last post Today at 06:12:52 PM
by Don P
xx
F.F. pavilion build.

Started by Jeff on Timber Framing/Log construction

249 Replies
9432 Views
Last post April 06, 2021, 09:46:46 AM
by Magicman
 


Powered by EzPortal