The Forestry Forum

General Forestry => Sawmills and Milling => Topic started by: paul case on January 06, 2012, 08:53:50 AM

Title: sawing speed on an lt40 w 24hp onan
Post by: paul case on January 06, 2012, 08:53:50 AM
Before I start I am aware speed is effected by width of cut , sharpness of band, ect.
I have been looking at an 94 or so LT40 with 24 hp onan.I was wondering  if it will saw as fast as my ez boardwalk mill, which seems to cut fine, but is all manual, and log handling  and sawing as much as I have been lately is terribly hard on the body.
I know that if I saw 1000 ftof framing lumber in 8 hours is an extremely good day on my mill.
If you have an lt40 24hp onan what can you saw in a day?
And maybe what would you change about your mill?

PC
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: Chuck White on January 06, 2012, 05:54:46 PM
Hello Paul;  I have the same mill, but mine is a 1995.

Sawing White or Red Pine, or Hemlock, Poplar, I usually get between 1,500 & 1,800 board feet of mixed 1X & 2X in a day (day = 8-10 hours) and call it a good day!
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: customsawyer on January 06, 2012, 07:04:37 PM
How many bf per hour are you getting now? I would think that if you add hyd. it would let you do a lot more. I can't add to your question since the smallest engine I have run is a 42 hp Kubota diesel. With that being said when I ran that mill I could expect to get about 3500 bf per day on a portable job with out a edger. If you are thinking about running this mill stationary I would think that you should be able to hit 2000 bf or a little better.
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: WH_Conley on January 06, 2012, 09:41:14 PM
Customsawyer called it about right, plus, the back will feel better.
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: paul case on January 06, 2012, 11:47:15 PM
I guess I will find out for myself.
I purchased JFarmer's dads lt40hd24 this afternnon. It needs a little work but he ran it some while I was over there and I believe it will be ok. I just needed something to take all the grunt work out and it sounds like I may easily double production.
I have to fix up a lube bottle, install a battery and maybe some new belts and she will be good to go. I don't have any blades for it , except the one that is on it, so I will have to get some of those ordered on monday. I am going to sell the ez boardwalk mill and I have a guy coming to look at it in the morning.
SO.......I guess we will see.   PC
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: WDH on January 06, 2012, 11:50:52 PM
I am jealous  :).
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: Chuck White on January 07, 2012, 07:29:25 AM
Good for you Paul.

The HYD WM will definitely be easier on your back.

The best I have ever gotten in a day was just over 2,300 board feet of mixed 1X & 2X White Pine.

That was a 10 hour day and there were 4 men off-bearing and feeding the log loader, there weren't very many breaks taken on that job either.

You will notice quite a jump in your daily production.
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: Mooney on January 07, 2012, 09:00:13 AM
Congrats on your purchase Paul! Glad you were able to get a deal and upgrade to the hydraulics. Feel free to call in today (before noon) or next week to get the mill transferred to your name and get your parts/blades ordered in. You'll also get a Owner Pack from us once you do.

Right now we're also scheduling our service loops for this year. It wouldn't hurt to check on how much it would run to have Bob swing through and get your mill running like new. He'll be servicing Arkansas/Missouri in September, and you're real close there. 

Title: Re: sawing speed on an lt40 w 24hp onan
Post by: sawman on January 07, 2012, 09:07:04 AM
 We started out with a manual lt 30, and upgraded to a lt 40hd, once we got use to the extra features, we doubled our production. Off hand I don't remember exact ## tho.
I think you will really like the hydraulics.

Congrats on the upgrade.
8) 8) 8) 8) 8) 8) 8) 8) 8) 8) 8) 8) 8) 8) 8) 8) 8) 8) 8) 8) 8) 8) 8) 8) 8) 8) 8) 8) 8)
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: customsawyer on January 07, 2012, 09:49:08 AM
Congrats on the purchase. Sorry though I didn't mean to talk you into it that fast. ;D
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: Slingshot on January 07, 2012, 10:15:13 AM

  Good move, Paul. You will love being able able to stand in one spot and
do in a few seconds what you used to have to run around the mill 3 or 4
times to do. Now you can fly. fly_smiley


____________________
charles  sling_shot



Title: Re: sawing speed on an lt40 w 24hp onan
Post by: pineywoods on January 07, 2012, 10:19:32 AM
Congrats on the new-to-you mill. Not only is it gonna be easier on your back, your feet and legs will thank you.. Not nearly as much running around the mill...
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: Larry on January 07, 2012, 10:58:38 AM
I think you made a very wise decision Paul.  Glad to see you get a new machine.
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: customdave on January 07, 2012, 01:25:00 PM
Congrats Paul, won't take but an hour to wonder why you didn't have hyds before now ;). Have fun with the new mill & play safe...


                                     Dave
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: plowboyswr on January 07, 2012, 01:41:38 PM
So did the EZ sell or can i still come get the tour?
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: fishpharmer on January 07, 2012, 02:05:08 PM
Congrats Paul!!  Your back will thank you.  8)
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: Buck on January 07, 2012, 02:57:57 PM
Paul, as you know there are many variables that can effect your production rate. I can tell you you will be proud of your purchase and your back will for sure feel much better also. Congratulations!  Give the ole girl a good once over and clean all the electrical connections you can find. The service route from Woodmizer is a very good investment. The technician will get you all checked out and you will learn a lot from being his helper.
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: paul case on January 07, 2012, 10:41:14 PM
I got the parts list started today.I pulled the muffler off to fix a few holes and got the oil draining and the oil filter off, which took the longest since it was really stuck. I am going to put new wheel belts on it before I start sawing.
One of the biggest things to figure out for me has to do with set up and not the mill at all. In order to be more efficient I will be racking up a few logs on some cants to roll onto the loader arms. In order to do that in a 40' wide building that has short sidewalls, as my chicken houses do, I will have to set the mill up  across the building, instead of along one wall as my boardwalk mill is now. I would like to set the thing up so that I could move boards right onto my cutoff table from the mill by hand instead of using the forklift as I am doing now.
Plowboyswr
The ez boardwalk is still set up and cutting. I would like to make someone a good deal on it. I guess I just as well list it for sale here on the forum. It is a good mill.
Thanks for all your kind and encouraging words about this. I highly value the friendships of you forum members. PC
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: Meadows Miller on January 08, 2012, 02:25:29 AM
Gday

And a Big Congrats Paul  ;) ;D ;D 8) 8) 8) 8) Your gonna be a WoodMizer Man now you know that Mate  :) ;) :D ;D ;D 8) 8)


Regards Chris
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: customsawyer on January 08, 2012, 06:42:33 AM
Does that mill have a drag back on it?
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: Larry on January 08, 2012, 06:58:23 AM
Roller conveyors might help with material handling.

Title: Re: sawing speed on an lt40 w 24hp onan
Post by: Meadows Miller on January 08, 2012, 07:37:35 AM
Gday

Paul what are the walls like in your shed steel or block work as you could just knock a hole in the wall and have say a 10' long pair of say 16x10 or 12" timbers for your deck (you could also cut them with a slight taper to make it easier to roll the logs to the loader too ;) )
as that might get you in enough hight wise for the mill as if you go length wise across the shed you may run out off room ;) and as Jake and Larry asked weather you have drag back and some roller beds It might also be wise to keep your Corley edger and get it fired up as it will make a big difference with handling your wing boards production wise Mate  ;) ;D ;D 8)

Regards Chris
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: Magicman on January 08, 2012, 09:44:45 AM
Good for you Paul !!!  I know that you have given this much thought and I'm excited for you. 
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: paul case on January 08, 2012, 02:57:10 PM
no drag back. no roller toe boards either.
I thought about the hole in the wall. My buildings have a steel truss every 10' so we would have to put a beam across 3 of them and cut the leg off the middle one. I don't think I want to do that. setting it across the building would leave about 12' to 14' at one end of it. The mill head could be rolled back so that the bed is all that sticks out in the building and my loader would get around the end of it, lifting long beams or boards over the mill bed.
I think I will give crossways a go, and if it don't work, I can always change it.
I am excited about it as well. I am looking foreward to wearing myself out sawing 2000 ft instead of just 1000 ft.PC
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: WH_Conley on January 08, 2012, 08:36:43 PM
Do you have concrete floor? Maybe an old wagon running gear to move finished product and slabs around?
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: WDH on January 08, 2012, 09:31:31 PM
Paul,

Do you normally tally and track your production?  I always record the BF and the engine hours that the mill actually ran as my LT15 does not have an hour meter.  My long term average has been 108 BF per sawmill engine running hour for 4/4 hardwood, but that does not count all time spent prepping, moving, and getting logs ready to saw.  That is the average with and without an offbearer.  I cannot average that by myself when cutting 4/4 hardwood.  I know that is not much, but somebody has to be small potatoes  :D.  I don't cut pine much at all, and 8/4 pine is where you can really make hay!  Cutting pine is like cutting butter with a hot knife. 

I enjoyed your posts about the EZ Boardwalk mill.  From what you have shown, I am impressed with it.  Hopefully it will go to a good home. 
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: paul case on January 08, 2012, 09:44:52 PM
Floors are real hard packed dirt in the buildings. I can move stuff around real efficiently with my forklift, but it burns gas too, and I am trying to eliminate some of the running it. My slabs will go in the same racks i used before and be moved outside and sold by the bundle.
WDH,
I have really enjoyed using that EZ boardwalk mill. I put 600 hours on it in a little more than 3 years. I ''cut my teeth'' with it, and it is by all means a good stout made mill that I can without reservation recomend to anyone wanting a manual mill.
I intend to cut for some level of production with the ''new'' one and I hope to get almost double what I have been sawing. However that may only be 4000 ft a week since I spend time logging and other farm stuff too. I have not kept track of the bdft. that I cut with it since quite a lot of it has been ties and cants, it would likely be a lot.
I quit putting up square baled hay and straw about 11 years ago because my shoulders were starting to give me a lot of pain, and lately sawmilling has been giving me the same pain or worse. I have high hopes that this will help me continue milling and not have to give that up. I really enjoy it.
Once again thanks for all of youalls encouraging words. PC
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: terrifictimbersllc on January 09, 2012, 05:15:40 AM
Just seeing this now, very happy for you, push them levers (& get yourself a spare hydraulic micro-switch)!
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: stavebuyer on January 09, 2012, 05:55:53 AM
Congrats on the mill upgrade Paul. The hydraulics will make life a little easier to be sure..and I hope you prove me wrong ....but I don't see the mill itself doubling your production in the products your producing. Banding and moving slab bundles, double handling the boards to be edged, how your set up to stack the cants & ties all probably take a toll on both your back and your production. Without decks and an edger; I would wager some of the better production numbers quoted were obtained from sawing longer length logs and or framing lumber(2x8's etc). The mill will cut more lumber easier and faster but if your working by yourself every board, slab, and cant still has to be handled. I have an LT70DCS and when I am cutting oak ties and 4/4 grade lumber by myself the mill does good to run two hours out of eight. The rest of time is stacking,banding, moving logs and or bundles.
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: paul case on January 09, 2012, 06:38:58 AM
I have put a lot of thought into this and found with the manual mill I was spending 1/3 of my time rolling and clamping logs. The lumber I edge had to be dragged back on the mill by hand. surely throwing the flitches on the loader arms and edging after every log will be a big help.
I have helped a friend who has an 97 lt40 some and his production was more than double mine. Surely it will help. Plus I can go mobile now if I choose. PC
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: slider on January 09, 2012, 07:33:22 AM
Bet your going to enjoy this mill paul.Be sure and get the manual with it.It makes a big difference when you are trying to get this thing cutting perfect.I started with a 40 and loved it.Mine had tow boards but no rollers .That was ok,my 70 came with roller tow boards,man what a difference.That and the drag back that customesawyer mentioned would make a big difference in your total Daley bdft.good luck  al
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: Peter Drouin on January 09, 2012, 07:34:20 AM
Best of luck to you PC , have fun :) :)
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: Magicman on January 09, 2012, 07:43:55 AM
I think that you are on track to definitely improve your "smile factor" at the end of a work day.    smiley_thumbsup    :)
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: paul case on January 11, 2012, 11:15:26 PM
Well today I wasn't smiling too much at the end of the day. It felt like having a new job.

I have been over the saw some and replaced the wheel belts and greased and lubed and changed engine oil as well as fixed the muffler and a few other maintenance issues. I sawed a log with it last night and did ok but today was another story. I was trying to saw up a 14' post oak about 19'' sed. I needed some 2x8 for a trailer flooring order. It seemed like the saw wasnt sawing as good as I thought it should so I put on a new blade. It was better but not what I expected. The 6/4 scale on the mill yeilded  boards that were 1 5/8 to 1 3/4 instead of 1 1/2. I was still having trouble with the lube set up I put on it.
The motor ran fine and was quiet compared to before. The up down was a little hard to get used to. The hydraulics worked good. I about had a fit getting the toe boards to work until I figured out the release was still open. The log was tapered so that when I sawed the second face and went to roll it wanted to go over the backstops, so I put a piece of pipe over the backstops and it rolled right over then. My back isn't sore but my mind is spent. It is just like learning a new trick. I am just a little bit older of a dog than the last time. PC
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: Jeff on January 12, 2012, 12:06:13 AM
I'm pretty sure the scales on the wood-mizer are grade scales. So 6/4 is going to return 6/4 plus an eighth.
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: Chuck White on January 12, 2012, 05:46:21 AM
The scales on the WM's allow for shrinkage.

Good thinking Paul, on using a length of pipe to extend the log stops!
My mill has a roller on top of each of the hyd. log stops.

Suggestion:  Read up on the sawmill tricks and tips.  There's a lot of good Wood-Mizer stuff there.
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: WH_Conley on January 12, 2012, 06:23:44 AM
See if your scale is held where you want by a wing nut. On my 97 the scale will come out and turn over. One side is for grade sawing, the other is actual thickness.
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: Magicman on January 12, 2012, 09:23:54 AM
Lower the toe board before turning the log, and yes, my scale has two sides.
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: paul case on January 12, 2012, 07:29:11 PM
I sawed a couple hours today but it was just too cold, 22 degrees or so.
i took the scale off and the other side was blank. I will have to do some adjusting on the scale, because it leaves the dog board 1 3/4 when set to cut at 1 /58 for a 1 1/2 board. I got along a little better with the cutting. I figured out that the lube wasn't working good enough so I will have to work on that some. the last blade I put on had sap build up on it real bad and wasn't cutting well through knots. With a new blade it cut fine.
The crossways set up isn't going to work. This saw does saw considerably slower than my ez boardwalk, so I thin I will be able to unload the boards from most logs while the saw is working. Even if I can't I still need both ends of the mill open so I can slide lumber and slabs off into stacks. This will put me throwing the sawdust toward the wall but I was planning to get a dust colector/ blower set up on this mill anyway. If I don't I could just pull it out and clean the dust out and then put it back. I may even be able to keep it a loader bucket width from the wall and take a sweep through there when it gets built up. Thats how I do on the ez.
Still working on learning this mill. PC
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: customsawyer on January 12, 2012, 07:47:48 PM
Don't get to frustrated as all new tools/equipment has a learning curve. I have every confidence that you will figure it out. I know that when I go from cutting with the mill in Hazelhurst to my portable mill there is always several mistakes. All are from my slow thinking ability.
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: paul case on January 12, 2012, 07:59:06 PM
I like to blame my shortfalls on the incompetent help. That would myself and I. Me does the sawing. ;D
I do feel better about the thing today. Yesterday I was ready to sell it for parts. I cut a log on the saw today and thought to turn it as a cant and it continued to measure true on each side as the opposite side. PC
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: paul case on January 14, 2012, 09:09:13 PM
I have figure out some of my troubles. I borrowed a couple blades from a neighbor and ramped up the water to the blade and that helped. Then I took to trying to shorten the first backstop. So much for a new blade. Rookie mistake. I have been spoiled by ez boardwalks fool proof saw. PC
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: Meadows Miller on January 14, 2012, 11:31:35 PM
These things happen Mate  ;) Jake was laughing his butt off when I left one off the tapers up and was gearing up to just start peeling boards off on the 70 ;) :D :D Took the first cut out off it and was thinking that should be alittle thicker down the far end  ??? :o >:(  smiley_furious3 he took pics too ;)  :D Just dropped the taper and started boarding off the rest off the log which didnt take long its the first time I had been back on a WM in about 5 years though  ;) ;D ;D 8) 8)
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: paul case on January 24, 2012, 11:35:36 PM
I got along with the new mill real well today. Most of the problems I had been dealing with is sap build up on the blade. I am not used to the water deal and I still don't have it down pat, but I am getting there. Sometimes the sawdust between the boards is a little dusty and then sometimes its muddy.
The sawing speed is a little slower than the boardwalk mill, but those hydraulics are the cat's meow! I am still working a few little bugs out but overall I am real happy with the 94 LT40hdg24 and I am sure it will give many more hours of good service.PC
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: plowboyswr on January 25, 2012, 12:57:46 AM
Glad to hear that youre getting along better now!  :D Thanks for treating my father inlaw so well he had nothin but praise for ya sunday when i saw him.  8)
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: bandmiller2 on January 25, 2012, 07:16:50 AM
Paul,you have those dandy big chicken houses,but I would consider building a smaller building over your mill.You could setup exactly what you want.Having a nice long dead deck will improve production.Something isn't just right with the WM,it should handily outcut the EZ,is it lack of power or band related,do you sharpen your own?Theirs a learning curve,don't beat your head agenst the wall it will come. Frank C.
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: ladylake on January 25, 2012, 07:32:06 AM

  If the hp on your EZ is close to 24 it sure could saw faster than the WM as it's not running a HD alternator and maybe the onan is tired or needs tuning.   Steve
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: paul case on February 10, 2012, 08:38:39 AM
Well now I know.
I got another order for 100 3x4 10'6'' cants on Tuesday. I was in the middle of 2 other orders and I didn't have any 10' logs. So I called the guys at the construction site where I had gotten quite a few logs and they said they could load me on Wednesday. Cants had to be done by Friday, today. On Wednesday I called and they said not today. So I didn't get the logs till Thursday at noon.
I got started about 1 and by 4 I had 50. I took a half hour break and started again and had another 25 by 6. Then ate supper and it took from 7 to 830 to cut the last 25. A coupleof the logs may have been bigger than when it took mejust over 8 hours to cut 100 cants with the ez boardwalk mill, but it only took 6 hours with the WM. Also there was no bark restriction on the last bunch from the ezboardwalk , but the ones I cut last night could not have any bark, so I spent quite a bit of that 6 hours cutting bark off the edges with a knife or hatchet.
Oh and did I mention I didn't feel good yesterday? my whole family has been dealing witha sinus infection and flu bug and I got it. I couldn't have sawn very much with the ez boardwalk mill yesterday without hurting a whole lot. I was tired when I got done last night but I wasn't totally exhausted.
The whole point is it definately is better. Easier on the body. I do find myself doing some of the offbearing while the mill is making a cut and that helps speed things up.
PC
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: Meadows Miller on February 10, 2012, 09:01:42 AM
Gday Paul

Its a good trick aint it Leave the mill cutting the next board while your tailing out Mate thats why I say 35hp plenty on a smaller mill when your working alone most off the time as the saws just getting through the cut quicker  ;) :D :D

Regards Chris
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: Stephen1 on February 11, 2012, 12:43:18 PM
Quote from: Mooney on January 07, 2012, 09:00:13 AM
Congrats on your purchase Paul! Glad you were able to get a deal and upgrade to the hydraulics. Feel free to call in today (before noon) or next week to get the mill transferred to your name and get your parts/blades ordered in. You'll also get a Owner Pack from us once you do.

Right now we're also scheduling our service loops for this year. It wouldn't hurt to check on how much it would run to have Bob swing through and get your mill running like new. He'll be servicing Arkansas/Missouri in September, and you're real close there.
Owner Pack...a freebie 8) sign me up, I never got an owner pack for registering my used LT40 Do I have to live south of the border for that?
I am picking up my mill tomorrow at the Canadian head office, it has been in for a tune up before a big job that starts tuesday
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: Chuck White on February 11, 2012, 01:01:14 PM
Paul, you can get additional cutting scales for your mill, they have an adhesive backing.

You just get it lined up to where you want it and remove the protective backing, then press it securely into place.
Title: Re: sawing speed on an lt40 w 24hp onan
Post by: customsawyer on February 11, 2012, 01:35:56 PM
I am glad that it is starting to work out for you. The more you use it the tricks you will figure out to speed things up and make it more productive. ;)