The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems

Chainsawr, The Worlds Largest Inventory of Chainsaw Parts

Smith Sawmill Service



Author Topic: HD36 sawhead problem  (Read 1836 times)

0 Members and 1 Guest are viewing this topic.

Offline Kllisk

  • member
  • *
  • Posts: 8
  • I'm new!
    • Share Post
HD36 sawhead problem
« on: August 17, 2018, 07:04:26 PM »

HD36 sawhead problem
I went through all the steps up to lumber scale calibration, had my clearance on blade guides this was all done with the adjustable blade at the widest position, went to adjust blade guide in and felt resistance, spun the blade and could hear it rubbing ceramics.This all because the sawhead shelf is unlevel but has to be to make the blade level with the bunks. Thought well I will level the adjustable blade guide under the sawhead shelf but then the detent system that holds the blade guide in place is locked because it is mounted to the gaurd bracket.

Offline Kllisk

  • member
  • *
  • Posts: 8
  • I'm new!
    • Share Post
Re: HD36 sawhead problem
« Reply #1 on: August 22, 2018, 04:08:44 PM »
I had called Norwood Monday and talked to Tom about it, he said he needed to do some research,he did not call Tue. so I called him today Wed. and he directed me to release blade tension and drive belt tension then tightened blade and gave it a few spins and I heard a thunk,checked level and it was a lot better (not perfect).Called him back and he directed me to shim down the top of the pivot bolt on drive axle with washers. Walla almost perfect!!! Now moveable blade guide only pushes down maybe two paper thicknesses when all the way in. Slowly learning these are not precision machines!! And a thanks goes out to Tom@Norwood


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
Power Sawhead (Up/down only) option Norwood HD36

Started by Rickcnc on Sawmills and Milling

0 Replies
678 Views
Last post May 16, 2016, 04:32:30 PM
by Rickcnc
xx
Norwood HD36 blade guides - problem removing Allen screws

Started by TmbrWlkr on Sawmills and Milling

15 Replies
829 Views
Last post March 31, 2021, 06:37:34 PM
by Patrick NC
xx
help on sawhead up & down travel

Started by bruce29 on Sawmills and Milling

5 Replies
1504 Views
Last post March 09, 2010, 06:06:38 AM
by ladylake
xx
Sawhead vibration

Started by gator gar on Sawmills and Milling

16 Replies
2792 Views
Last post July 02, 2010, 10:50:42 PM
by paul case
 


Powered by EzPortal