The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems

Chainsawr, The Worlds Largest Inventory of Chainsaw Parts

Smith Sawmill Service



Author Topic: FAILURE: Blade Tensioner Thrust Bearing  (Read 1480 times)

0 Members and 1 Guest are viewing this topic.

Offline Riversedge

  • member
  • *
  • Posts: 4
  • I'm new!
    • Share Post
FAILURE: Blade Tensioner Thrust Bearing
« on: April 25, 2021, 09:39:17 PM »
While running my 2020 Woodland Mills HM126 today the blade tensioner thrust bearing failed rather dramatically. With the sound of a rifle shot the mill released ALL the blade tension at once. Immediately the t-handle was reversed out of the machine and dangled from its shaft. This in turn threw off the blade immediately grabbing the guide arm shield and ripping it from the machine. In the process the shield was folded up like a UFC fighter taking a dive. It also appears to have damaged the ceramic blade guides and bent the guide arm slightly. I didn't think it was possible to bend a bandsaw blade but take my word for it; It is.

Upon removal of the thrust bearing and examining it you could see that it was filled with metal shavings. I also looked at the t-handle threads and they all appeared fine. I have to say that I have been thoroughly enjoying this machine until now. With just under 12 hours on it, this is not a part that I expected to fail so flamboyantly.

Has any one else had this issue with their Woodland Mills Sawmill?

I should add that everything was properly lubed and the tension properly set per the manual.

Thanks.

Offline Southside

  • Administrator
  • *****
  • Posts: 9060
  • Age: 49
  • Location: Wilsons (Dinwiddie County), VA
  • Gender: Male
  • Have a plan to saw every log you meet.
    • Share Post
    • White Oak Meadows
Re: FAILURE: Blade Tensioner Thrust Bearing
« Reply #1 on: April 25, 2021, 09:46:38 PM »
Welcome to the Forum.  I would say contact Woodland.  They didn't make the bearing, they buy them, and things break - so give them the opportunity to make it right given it's such a new mill.  

By the way bands break in a similar fashion, not sure what is in the path of destruction on your mill when that happens but I have had to dig a few pointy snake pits out of my mills.   
Franklin buncher and skidder
JD Processor
Woodmizer LT Super 70 and LT35 sawmill, KD250 kiln, BMS 250 sharpener and setter
Riehl Edger
Woodmaster 725 and 4000 planner and moulder
Enough cows to ensure there is no spare time.
White Oak Meadows

Offline btulloh

  • Senior Member x2
  • *****
  • Posts: 4076
  • Age: 69
  • Location: Midlothian, VA
  • Gender: Male
  • I never met an air conditioner I didn't like
    • Share Post
Re: FAILURE: Blade Tensioner Thrust Bearing
« Reply #2 on: April 25, 2021, 10:11:55 PM »
Certainly not a typical failure. Some sort of manufacturing defect. Never even heard of this type of failure. Like Southside said, call them first thing in the morning. They will be anxious to help and get the problem solved quickly. 

Sorry to see you run into such a major issue after only twelve hours. They have been very good with support over the four years I’ve been running that same mill. I’ve never had anything but a couple very minor issues but they’ve been all over those and even sent me free upgrades during the warranty period. 

Your problem will be more of a challenge to get sorted out but they’ll get it taken care of. 
HM126

Offline Riversedge

  • member
  • *
  • Posts: 4
  • I'm new!
    • Share Post
Re: FAILURE: Blade Tensioner Thrust Bearing
« Reply #3 on: April 25, 2021, 10:23:55 PM »
Thanks for the reply’s. I have called and left a message for them to  call me back but I will be sure to ping them again first thing tomorrow. 

I agree this seems like a weird failure and not something very common. 

I have been so impressed with WM customer service so far. When I ordered I was told it would be 12 weeks before delivery and received it 3 weeks early. 

Offline Riversedge

  • member
  • *
  • Posts: 4
  • I'm new!
    • Share Post
Re: FAILURE: Blade Tensioner Thrust Bearing
« Reply #4 on: April 27, 2021, 10:06:00 PM »
UPDATE: Woodlandmills did me right. They replaced my thrust bearing plus the T-handle, blade guide shield and my saw blade with no questions asked. 

Thank you Woodlandmills For the excellent customer service. 


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
TK blade tensioner failure

Started by Ga Mtn Man on Sawmills and Milling

15 Replies
1501 Views
Last post November 10, 2012, 06:51:24 PM
by Sawdust Lover
xx
Post thrust failure calculation

Started by fromrfarm on Timber Framing/Log construction

1 Replies
403 Views
Last post March 25, 2020, 08:50:34 AM
by fromrfarm
xx
Bearing failure.

Started by Grower on Sawmills and Milling

13 Replies
2397 Views
Last post November 04, 2011, 12:56:05 AM
by Grower
xx
Bent rim and possible wheel bearing failure.

Started by slice107 on General Board

2 Replies
119 Views
Last post Today at 02:58:06 PM
by YellowHammer
 


Powered by EzPortal