The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems

Chainsawr, The Worlds Largest Inventory of Chainsaw Parts

Smith Sawmill Service



Author Topic: Accuset2 Setworks question?  (Read 879 times)

0 Members and 1 Guest are viewing this topic.

Offline 038magnum

  • member
  • *
  • Posts: 43
  • Age: 62
  • Location: Hardy, Virginia
  • Gender: Male
    • Share Post
Accuset2 Setworks question?
« on: October 20, 2012, 12:43:31 PM »
I have been playing some with my new mill cutting 1 1/8" boards. I had Accuset programed with the correct kerf for the blade that I am using. The mill started out cutting 1 1/8" thick. next day it was 1 3/16". Now it is cutting 1 1/4". What might be causing this?

Offline Bibbyman

  • Senior Member x2
  • *****
  • Posts: 11426
  • Age: 71
  • Location: In the middle of things
  • Gender: Male
  • Pro-Sawyer Mary and Bibbyman
    • Share Post
    • Warden Sawmill
Re: Accuset2 Setworks question?
« Reply #1 on: October 20, 2012, 12:59:31 PM »
Just occasionally?  Or every board?

I'd say a conversation with Sparks at Wood-Mizer would get you back on track quicker.

I've never had that happen.
Wood-Mizer LT40HDE25 Super 25hp 3ph with Command Control and Accuset.
Sawing since '94

Offline rmack

  • Senior Member
  • ****
  • Posts: 433
  • Age: 63
  • Location: South end of the Cariboo Plateau
  • Gender: Male
  • Woodmizer owner
    • Share Post
Re: Accuset2 Setworks question?
« Reply #2 on: October 20, 2012, 02:28:39 PM »
2 cents from the uneducated... sounds like a reference point moving.

Does your bottom of low tooth to deck measurement still jive?
the foundation for a successful life is being able to recognize what to least expect the most... (anonymous)

Welder Bob
2012 LT40HDSD35 Yanmar Diesel Triple
1972 Patrick AR-5
Massey Ferguson GC2410TLB Diesel Triple
Belsaw Boat Anchor

Online terrifictimbersllc

  • Senior Member x2
  • *****
  • Posts: 5882
  • Age: 67
  • Location: Mystic, CT
  • Gender: Male
    • Share Post
    • Terrific Timbers LLC
Re: Accuset2 Setworks question?
« Reply #3 on: October 20, 2012, 04:36:19 PM »
.....and have you ruled out the cant moving from stress, this throws board thicknesses all over the place (usually ends thinner and middles thicker).
DJ Hoover, Terrific Timbers LLC,  Mystic CT Woodmizer Million Board Foot Club member. 2019 LT70 Super Wide 55 Yanmar,  LogRite fetching arch, WM BMS250 sharpener/BMT250 setter.  2001 F350 7.3L PSD 6 spd manual ZF 4x4 Crew Cab Long Bed

Offline 038magnum

  • member
  • *
  • Posts: 43
  • Age: 62
  • Location: Hardy, Virginia
  • Gender: Male
    • Share Post
Re: Accuset2 Setworks question?
« Reply #4 on: October 20, 2012, 06:45:37 PM »
Thanks for the advice. I will play more with it tomorrow.


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
Timberking Setworks Question

Started by Tasha on Sawmills and Milling

8 Replies
435 Views
Last post January 18, 2022, 01:33:45 AM
by Tasha
xx
Corley setworks question

Started by Dave_ on Sawmills and Milling

15 Replies
3951 Views
Last post December 23, 2010, 09:57:30 PM
by captain_crunch
cheesy
Setworks Question for TimberKing 2000

Started by kgbond on Sawmills and Milling

9 Replies
1613 Views
Last post May 22, 2012, 09:05:42 PM
by WDH
xx
accuset vs. accuset2

Started by rooster 58 on Sawmills and Milling

18 Replies
1283 Views
Last post January 08, 2013, 07:04:32 AM
by MartyParsons
 


Powered by EzPortal