The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems

Chainsawr, The Worlds Largest Inventory of Chainsaw Parts

Smith Sawmill Service



Author Topic: Valmet 546h  (Read 266 times)

0 Members and 1 Guest are viewing this topic.

Offline Angrybeaver94

  • member
  • *
  • Posts: 20
  • I'm new!
    • Share Post
Valmet 546h
« on: October 16, 2021, 01:06:15 PM »
 
iI got a Valmet 546h with a Cranab 998 slide boom. The hoses and chain keeps getting slack in them and the hoses walk off the wheel once in a while and get pinched. When I tighten the slack in the hoses itís usually good for a couple months then gets slack in them again. Any ideas wht could cause this? 

Offline Gary_C

  • Senior Member x2
  • *****
  • Posts: 7133
  • Age: 79
  • Location: Blooming Prairie, MN USA
  • Gender: Male
  • Sunrise on the Prairie
    • Share Post
Re: Valmet 546h
« Reply #1 on: October 16, 2021, 01:54:09 PM »
Yes, but there is no cure.

Here are a few reasons and advice.
1. Hoses stretch.
2. When hoses stretch keep adjusting the tension.
3. Make sure the hoses are in their proper slots in the wheel.
4. When hoses get damaged and kinky, replace them.
5. Make sure the sag is the same for all hoses.
Never take life seriously. Nobody gets out alive anyway.

Offline Angrybeaver94

  • member
  • *
  • Posts: 20
  • I'm new!
    • Share Post
Re: Valmet 546h
« Reply #2 on: October 16, 2021, 03:49:35 PM »
I had taken a link out of the chain about a couple months ago and tightened it up and even the chain has slack in it again. 


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
Valmet 960

Started by Drew78 on Wanted

0 Replies
846 Views
Last post July 07, 2015, 12:02:19 PM
by Drew78
xx
valmet 840.2

Started by cbutler703 on Forestry and Logging

0 Replies
670 Views
Last post September 08, 2016, 02:29:57 PM
by cbutler703
xx
valmet 603

Started by treefarmer87 on Forestry and Logging

2 Replies
2006 Views
Last post June 03, 2011, 10:25:08 PM
by treefarmer87
xx
Valmet 646

Started by bmcel253 on Forestry and Logging

5 Replies
2200 Views
Last post September 18, 2015, 06:53:18 AM
by snowstorm
 


Powered by EzPortal