The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems

Chainsawr, The Worlds Largest Inventory of Chainsaw Parts

Smith Sawmill Service



Author Topic: Shiplap  (Read 1716 times)

0 Members and 1 Guest are viewing this topic.

Offline Bandit

  • member
  • *
  • Posts: 3
  • Location: Norridgewock, Maine
  • I'm new!
    • Share Post
Shiplap
« on: April 29, 2007, 05:37:23 AM »
Want  some input on milling shiplap and tounge and groove lumber.  I own a sawmill and woodmaster planner/moulder.  Want only enough to do inside and outside of 30X32 garage.  Can do with planner but, seems like much set up and not certain I can do wider than 6".  Someone mentioned a router?  Any ideas?

Ron

Online WH_Conley

  • Senior Member x2
  • *****
  • Posts: 4119
  • Age: 65
  • Location: Camp Dix, Ky.
  • Gender: Male
  • I need to tide my profile!
    • Share Post
    • Stone Hill Hardwoods
Re: Shiplap
« Reply #1 on: April 29, 2007, 08:07:45 AM »
Can't give you much info on shiplap, but use the search unction, you will find a lot of info, pros and cons of different methods.
 
Welcome to the forum.
Bill

Offline solodan

  • Senior Member
  • ****
  • Posts: 775
  • Location: sugarpine Ca.
  • Gender: Male
    • Share Post
Re: Shiplap
« Reply #2 on: April 29, 2007, 12:04:27 PM »
shiplap is pretty easy to do with just a table saw. :)

Offline Ianab

  • Administrator
  • *****
  • Posts: 14966
  • Age: 59
  • Location: Stratford , New Zealand
  • Gender: Male
  • Marmite on toast is a real breakfast
    • Share Post
Re: Shiplap
« Reply #3 on: April 29, 2007, 05:45:52 PM »
I do small amounts of shiplap and T&G using my big 3hp router and a homemade router table. Works OK for small amounts, making toyboxes and fish tank stands etc. But I think if I was panelling a whole building (Twice) I'd either be looking for a shaper with a power feeder or hiring the job out to someone with a multihead planer / moulder.

A dedicated shaper might be a good investment to go with your other gear though?

Cheers

Ian
Weekend warrior, Peterson JP test pilot, Dolmar 7900 and Stihl MS310 saws and  the usual collection of power tools :)


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
miles of shiplap

Started by hackberry jake on General Woodworking

18 Replies
3024 Views
Last post October 16, 2016, 08:02:26 AM
by Just Me
xx
Making shiplap.

Started by Dave Shepard on General Woodworking

11 Replies
752 Views
Last post May 01, 2021, 11:09:57 AM
by Bruno of NH
xx
CSM: Shiplap - Rough Cut

Started by Lost in the Outback on Sawmills and Milling

6 Replies
1778 Views
Last post April 19, 2013, 07:59:18 PM
by losttheplot
xx
cutting shiplap on a mill

Started by woodweasel on Sawmills and Milling

18 Replies
3821 Views
Last post April 21, 2014, 08:30:36 AM
by 36 coupe
 


Powered by EzPortal