Author Topic: Tools for Timber Framing List (Read 184008 times)

Brad_bb · « **Reply #40 on:** May 14, 2012, 10:33:54 AM »

Speaking of axes, Moonhill and I just had this conversation...I've been keeping my eye out for a certain axe for timberframing. I used one Collin Beggs had that I really liked. It's smaller than a felling axe, but larger than a hatchet. Moonhill and I figured about 27-29 inches long overall, about a 2.25 lb head, with true fawns foot. We also talked about the beard and jaw, and basically it has to have some curve to it and not be straight across. I don't usually see many around where I live, but I'm keeping my eye out for what we named the "moma bear" axe.

laffs · « **Reply #41 on:** May 17, 2012, 09:05:15 PM »

is it what they call a pole axe or trappers axe

robertbeard82 · « **Reply #42 on:** October 13, 2012, 10:08:32 PM »

I am looking for a chain mortiser, does anyone have one they would be willing to sell?

Jim_Rogers · « **Reply #43 on:** October 15, 2012, 01:55:55 PM »

If they had one to sell it would be listed in the "for sale" section. Not here.

And if you want to buy one you should list your request in "wanted".... not here.

Your new post here is not in the right place.

But I think I'll leave it so that others will understand how find one and where to look.

Jim Rogers

Solomon · « **Reply #44 on:** February 19, 2014, 04:37:00 PM »

I have three very old Skill Worm Drive Saws. The Blades measure 11 and 5/8 and the saws and blades are dimond arbors. Two of them are in good condition in the steel carry cases they came in from the manufacturer. One has the book with it.
Are theese saws useful for Timber Framing ? I know they were used in the Hold of ships to cut caulking dunnage. Usually 8x8 and larger Oak. Anybody know anything about them?
They look like you could cut your leg of if you wern't paying attention and holding on tight.
I think theese worm drive saws have a lot of torc. They weigh about 35 or 40 pounds a piece.

WOOD100 · « **Reply #45 on:** June 09, 2016, 12:29:30 PM »

Thank you very much for all the information, it helped me a lot. What do you think about locust tree for framing? I have at the disposal a lot of locust trees, unfortunately I can't tell the difference between Honey locust and Black locust. I also need a new circular saw, I found some positive reviews about Makita, see here for example. What do you think about circular saws with left mounted blade? It should improve the visibility.

Jim_Rogers · « **Reply #46 on:** June 09, 2016, 04:20:11 PM »

You could/should start a new thread for each new subject.
Locust is good for pegs, I haven't framed with it.
All saws have their benefits and disadvantages.
You'll need to pick one or two for yourself.

Jim Rogers

TimFromNB · « **Reply #47 on:** April 17, 2017, 02:12:54 PM »

Question for Jim Rogers:

Have you been able to test the new layout tool from TFHQ?

Would you recommend it over the original from TFG considering the increased cost?

Thanks,
Tim

Dave Shepard · « **Reply #48 on:** April 17, 2017, 04:10:05 PM »

I've used it, don't like it.

Jim_Rogers · « **Reply #49 on:** April 17, 2017, 09:43:21 PM »

I have used it many times. I love it. Of course it is a bit different then the original Big Al but once you get going with it you'll wonder why they didn't put the rules on the original Big Al in the first place.

Due to all the rules all over every slot and all edges it costs more. But it is worth it in my opinion.

It's a bit larger so it's a bit heavier.

If you have any specific questions please ask.

Jim Rogers

TimFromNB · « **Reply #50 on:** April 18, 2017, 05:41:58 AM »

Great, thanks for your feedback. They are expensive for us Canadians with the current exchange rate, but I am hoping this will pay-off in time savings.

Chevy2 · « **Reply #51 on:** September 15, 2018, 07:49:25 AM »

Excellent thread!
As a novice about to tackle my first timber frame build, I have spent hours here reading up on various topics concerning the "Do's & Don't's" on just about all of proceedures of a build (I still have a few to go).

After reading this thread, I would like to get some input about tools. For the most part, I have a vast majority of the tools with only a couple of items that I will need to pick up.

What I am interested in here is about chisels and slicks from the experts in the field. Specifically what to look for when shopping around ... Recommendations (that will not break the bank) ... Pro's & con's of various manufacturers ... Etc.

My thanks to this sight for the loads of information!

ljohnsaw · « **Reply #52 on:** September 16, 2018, 12:02:06 AM »

I have a 2" slick I picked up off of eBay. Crusty, rusty - it took a bit of work to clean it up. I has a socket for the handle. I made one from an old (hickory?) shovel handle. I put a copper collar on it so I could hit it with a mallet. After finally actually using it yesterday, I now know I did it all wrong! I made a handle that was about 16" long for a total length of about 24-28". The collar makes it very uncomfortable to push and the handle is way too short. I'm going to make a new handle with a ball end on it, kind of like a baseball bat. Might even cut down a bat and turn the end to fit the socket.

Sailor48NW · « **Reply #53 on:** February 20, 2019, 02:01:11 AM »

Hi Jim,

I'm interested in the Millers Falls boring machines you have up for sale. Are they still available? If so, could you please send pictures?

Millers Falls Boring Machines
#L10 and #Q10.

Thank You,
Aaron Johnson
Vancouver, Washington

SPACE AVAILABLE

Forestry Forum
Sponsored by: