iDRY Vacuum Kilns

Sponsors:

feedback wanted

Started by Ed_K, November 14, 2003, 06:01:58 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

Ed_K

 Just had my website updated. Will it work??? Pros & cons.
  http://mtdata.com/ede
 Thanks Ed
Ed K

Tom

Nice, clean looking site.  Easy to read too.  Put a reference in the Services Topic. It's a good place for advertising. :)

Fla._Deadheader

 Looks good to me ;D
  I hate sites where you spend all your time figgering out how to navigate. ::) :D
All truth passes through three stages:
   First, it is ridiculed;
   Second, it is violently opposed; and
   Third, it is accepted as self-evident.

-- Arthur Schopenhauer (1788-1860)

BW_Williams

Very nice Ed.  Did you "build" it or pay someone?  I've been looking at Jeff's deal for members, but Don't know a HMTL from a hole in the ground!  BWW
Support your local Volunteer Fire Dept.  (not by accident)
Support your local Ski Patrol (by snowboarding:)
Mayor of Millerdale, Washington, USA (by God)!

VA-Sawyer

Looks pretty good to me. 8)

Frank_Pender

Fine presentation of what it is you are all about.   ;D
Frank Pender

sawwood


 Nice looking site Ed. It is good looking and easy to move
 around in. Stright to the point what you do and don't do.
 I like it alot.

 Sawwood
Norwood M4 manual mill, Solar Kiln, Woodmaster
18" planer/molder

Gus

Completly idiot proof, easy to read and nice examples. Way to go Ed
Gus
"How do I know what I think unless I have seen what I say?"

dan-l-b

Hey Ed,  I really like yourconcept/website. 8)  Initially in the TSI section  you say you match the equipment to the job size.  Does that mean you rent some of your equipment or just have a large pool of equipment to pick from?  How long have you been providing this type of service?  You might want to mention that.  In the cordwood section I was anticipating a picture of your processor-  :'( :'( I will get over it. :D Not to be picky and I ain't no english major but, there were a few spots I had to reread to get the train of thought.   :) :)  All and all, however, a really good site.

Small scale logging/low impact TSI are very interesting ot me.  Is this something you are doing full time?  Are you making living at it?

Good Luck, Dan

GAV64

Ed,
Nice site, informative and concise. Question? is Leyden actually West Leyden, if it is you have a gem of a river valley. I have some property in Colrain up on Franklin Hill, can't get enough of it, beautiful place. Glenn

Ed_K

 Thanks to all, on the feed back.
 B.W. actually I trade work hours for the web site work, I used to write programs for vertical machining centers, but html is better left to my builder.
Ed K

Ed_K

 Thanks to all, on the feed back.
 B.W. actually I trade work hours for the web site work, I used to write programs for vertical machining centers, but html is better left to my builder.
 Dan-l-b, I've been in the loging/land clearing for 4 yrs, but just started concertrating on the tsi side. I have the equipment to do the different types of of low impact logging, but it was a hard go to aquire them. The processor is homemade, and not something I'm proud of, its to slow. But its usefull for odd length sorts.
 Gav64, West Leyden is part of leyden town, we're real proud of the green river, its classified as a cold water fisheries, not many in Ma.
 Thanks again to all.
 Ed
Ed K

GAV64

Ed,
Any chance the next time I am up in Colrain that I could get a look at your processor, I am itching to make one but not sure exactly how  & where to start.glenn

sawman

    Nice site, easy to navigate.
'14 LT40 Hydraulic 26 HP koehler ,massey ferguson 2200 forklift, Case IH D40
Wallenstein FX85

Bill Johnson

Very nice site. Easy to read and no technical terms to confuse the easily confused ???
Bill

Ed_K

 Gav 64, give us a call. your welcome to stop by any time.
 All are welcome.
 Ed
Ed K

Thank You Sponsors!