iDRY Vacuum Kilns

Sponsors:

Is the Customer ALWAYS right? If its his money!

Started by POSTON WIDEHEAD, October 25, 2012, 05:33:46 PM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

Print
Go Down Pages 1 2 3 All
User actions

Magicman

#50
October 30, 2012, 08:30:31 AM
I love it.  I also loved the "gotcha" at the end.   :D
98 Wood-Mizer LT40 SuperHydraulic    WM Million BF Club

Two: First Place Wood-Mizer Personal Best Awards
The First: Wood-Mizer People's Choice Award

It's Weird being the same age as Old People

Never allow your Need to make money
To exceed your Desire to provide Quality Service

paul case

#51
October 30, 2012, 08:45:56 AM
Holie wood!!!!  nice floor. I make a good use out of those dead trees too. I try to get them before the bark starts to flake off and before the 1'' branches start to fall off and they make some real nice lumber and cants. Plus no one can fault you for cutting a dead tree. It aint like I killed it!  PC
life is too short to be too serious. (some idiot)
2013 LT40SHE25 and Riehl edger,  WM 94 LT40 hd E15. Cut my sawing ''teeth'' on an EZ Boardwalk
sawing oak.hickory,ERC,walnut and almost anything else that shows up.
Don't get phylosophical with me. you will loose me for sure.
pc

POSTON WIDEHEAD

#52
October 30, 2012, 09:33:17 AM
Beautiful Barbender. Did you and your customer get along installing this floor?  :)
The older I get I wish my body could Re-Gen.

WDH

#53
October 30, 2012, 08:29:55 PM
I bet that knothead is a hard dude to work for  :D :D. Nice job!
Woodmizer LT40HDD35, John Deere 2155, Kubota M5-111, Kubota L2501, Nyle L53 Dehumidification Kiln, and a passion for all things with leafs, twigs, and bark.  hamsleyhardwood.com

Okrafarmer

#54
October 30, 2012, 09:34:30 PM
Through his whole post, I was  ???  , trying to think, I don't remember doing those things!
He that dwelleth in the secret place of the most High shall abide under the shadow of the Almighty. Psalm 91:1

Operating a 2020 Woodmizer LT35 hydraulic for Upcountry Sawmill, Dacusville, SC

Now selling Logrite tools!

Writing fiction and nonfiction! Check my website.

barbender

#55
October 31, 2012, 01:14:08 AM
Actually, though I am the "knothead" in the story (and many others come to think of it ::)) the real customer in the end would be Mrs. Barbender, and she like ;) I should probably start a new thread on our house project, there is a lot of "character" wood being used in it. Like the White pine T&G ceiling, had it sawn 11 years ago (before I had a mill), it sat stickered but uncovered for 2 years, got it planed then it sat under an open shed until it got installed last winter. The pine got a lot of brown stain from getting wet, then after it was planed some of the ends were exposed in the stack and got sun stained. I cleaned it up and danG if it don't look purty. I wouldn't recommend my methods, BTW, but once in a while in the chaos of having too many irons in the fire I pull out a winner ;D
Too many irons in the fire
Print
Go Up Pages 1 2 3 All
User actions

Thank You Sponsors!