The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

FARMA


Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems

Chainsawr, The Worlds Largest Inventory of Chainsaw Parts





Author Topic: Door clearance on Virginia Tech kiln design  (Read 247 times)

0 Members and 1 Guest are viewing this topic.

Offline Pepe_Silvia

  • Full Member x2
  • ***
  • Posts: 110
  • Age: 34
  • Location: Plano, TX
  • Gender: Male
    • Share Post
Door clearance on Virginia Tech kiln design
« on: April 04, 2019, 09:32:00 PM »
This is more of a general construction question, but since it's technically for a kiln, I thought I might ask here.

How much space would be acceptable between the door and the door framing?  Couple inches?  I'll be covering it in 7/16" solarbord, then siding, so I figure I can cover most of the gap with one of those, or when I trim it out.

My biggest concern is that (I don't know if you can see this in the pictures) it bows up a bit in the middle - turns out the trailer frame wasn't actually all that true, so the gap will be bigger on the ends than middle.

Also, while I'm asking, any recommendation on what type of hinges I should be using?





 

Online btulloh

  • Senior Member x2
  • *****
  • Posts: 2659
  • Age: 67
  • Location: Midlothian, VA
  • Gender: Male
  • I never met an air conditioner I didn't like
    • Share Post
Re: Door clearance on Virginia Tech kiln design
« Reply #1 on: April 04, 2019, 10:40:18 PM »
I used 6 strap hinges and theyre doing fine. I did put in little hardwood piece near the middle for each door to rest on when the doors are closed to take the strain off the hinges.

Itll be ok to leave a gap to work around whatever issues youre dealing with. Just make sure your door seals take care of it.
HM126

Online YellowHammer

  • Senior Member x2
  • *****
  • Posts: 4620
  • Age: 55
  • Location: New Market, Alabama
  • Gender: Male
  • Take Steps to Save Steps
    • Share Post
    • Hobby Hardwood Alabama
Re: Door clearance on Virginia Tech kiln design
« Reply #2 on: April 04, 2019, 10:57:27 PM »
Gaps can be dealt with seals, the kiln doesnt have to be airtight, but it does have to be tight enough to utilize the heat.  I left some gaps between the door frame and door, but covered the gap with the siding and used a face seal so that when the doors close they close agains the seal.  
HobbyHardwoodAlabama.com


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
Shooting at Virginia Tech

Started by Wudman on General Board

17 Replies
3490 Views
Last post April 20, 2007, 04:54:20 PM
by Don P
xx
Virginia Tech Memorial - Thank You

Started by mechengineer13 on Sawmills and Milling

3 Replies
1252 Views
Last post April 22, 2007, 12:41:38 PM
by twobears
xx
Dry Kiln Operator's Short-Course at Haywood Tech

Started by Whitster on Forest Education

0 Replies
1670 Views
Last post July 08, 2010, 11:08:15 AM
by Whitster
xx
Kiln door?

Started by WoodChucker on Drying and Processing

5 Replies
1292 Views
Last post July 21, 2004, 06:11:09 PM
by WoodChucker
 


Powered by EzPortal