The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems

Chainsawr, The Worlds Largest Inventory of Chainsaw Parts





Author Topic: Edger  (Read 673 times)

0 Members and 1 Guest are viewing this topic.

Online Bruno of NH

  • Senior Member x2
  • *****
  • Posts: 4149
  • Age: 54
  • Location: Springfield NH
  • Gender: Male
    • Share Post
Edger
« on: August 13, 2019, 05:20:57 PM »
Can't get my new edger to cut true curves off 
Any ideas 
I haven't used it much because it makes me mad been edging on the mill 
That's what I got the edger for.
Lt 40 wide with 38hp gas and command controls Riehl Steel edger,F350 4x4 dump and lot of contracting tools

Offline 47sawdust

  • Senior Member x2
  • *****
  • Posts: 1670
  • Age: 73
  • Location: worcester,vt.
  • Gender: Male
    • Share Post
Re: Edger
« Reply #1 on: August 13, 2019, 06:47:06 PM »
In feed/out feed dead level?
Mick
1997 WM Lt30 1999 WM twin blade edger Kubota L3750 Tajfun winchGood Health Work is my hobby.

Offline moodnacreek

  • Senior Member x2
  • *****
  • Posts: 1958
  • Location: Orange County NY
  • Gender: Male
  • Sawin by the notches
    • Share Post
Re: Edger
« Reply #2 on: August 13, 2019, 07:17:50 PM »
Not an unusual problem. What kind of feed , belts, rollers or chain?

Offline moodnacreek

  • Senior Member x2
  • *****
  • Posts: 1958
  • Location: Orange County NY
  • Gender: Male
  • Sawin by the notches
    • Share Post
Re: Edger
« Reply #3 on: August 13, 2019, 07:20:40 PM »
Oh yeah, spread the saws out and see how a board goes through.

Online Bruno of NH

  • Senior Member x2
  • *****
  • Posts: 4149
  • Age: 54
  • Location: Springfield NH
  • Gender: Male
    • Share Post
Re: Edger
« Reply #4 on: August 13, 2019, 07:22:39 PM »
Dead level
Feed rollers with chain
Lt 40 wide with 38hp gas and command controls Riehl Steel edger,F350 4x4 dump and lot of contracting tools

Online Southside

  • Administrator
  • *****
  • Posts: 6495
  • Age: 48
  • Location: Wilsons (Dinwiddie County), VA
  • Gender: Male
  • Have a plan to saw every log you meet.
    • Share Post
    • White Oak Meadows
Re: Edger
« Reply #5 on: August 13, 2019, 09:27:29 PM »
Check the out feed fence against the fixed blade, make sure it is dead square and at the same distance from the frame as the corresponding face of the blade, if it's not then it is pushing the lumber to the side as it passes by. 
Franklin buncher and skidder
JD Processor
Woodmizer LT Super 70 and LT35 sawmill, KD250 kiln, BMS 250 sharpener and setter
Riehl Edger
Woodmaster 725 and 4000 planner and moulder
Enough cows to ensure there is no spare time.
White Oak Meadows

Offline Peter Drouin

  • Senior Member x2
  • *****
  • Posts: 9405
  • Location: New Hampshire
  • Gender: Male
    • Share Post
    • A&P Saw mill LLC
Re: Edger
« Reply #6 on: August 14, 2019, 06:39:09 AM »
Did you not run it when you first got it?
A&P saw Mill LLC.
45' of Wood Mizer, cutting since 1987.
License NH softwood grader.

Online Bruno of NH

  • Senior Member x2
  • *****
  • Posts: 4149
  • Age: 54
  • Location: Springfield NH
  • Gender: Male
    • Share Post
Re: Edger
« Reply #7 on: August 14, 2019, 07:09:17 AM »
It's not cut right from the beginning I thought it might have something to do with the old mill
Lt 40 wide with 38hp gas and command controls Riehl Steel edger,F350 4x4 dump and lot of contracting tools

Online Sixacresand

  • Senior Member x2
  • *****
  • Posts: 2308
  • Age: 71
  • Location: Gordon, Georgia
  • Gender: Male
  • John and Nancy
    • Share Post
Re: Edger
« Reply #8 on: August 14, 2019, 07:20:16 AM »
Hang in there.  You will figure it out.  

Online Bruno of NH

  • Senior Member x2
  • *****
  • Posts: 4149
  • Age: 54
  • Location: Springfield NH
  • Gender: Male
    • Share Post
Re: Edger
« Reply #9 on: August 14, 2019, 07:24:51 AM »
Boards with a hook or varying width don't sell
Not what I was expecting 
Lt 40 wide with 38hp gas and command controls Riehl Steel edger,F350 4x4 dump and lot of contracting tools

Offline Oliver05262

  • Senior Member
  • ****
  • Posts: 390
  • Age: 76
  • Location: Shaftsbury, Vermont
  • Gender: Male
    • Share Post
Re: Edger
« Reply #10 on: August 14, 2019, 07:34:56 AM »
Bruno, have you asked Darren about the problem? He ought to be able to give you an idea of where to check for alignment of the rolls, the saw arbor and the guides. I suspect as Southside suggested that something is pushing against the board as it exits the edger. Good luck in figuring this out. 
"You can't do wrong by doing good"

It's OK to cry.

I never did say goodby to my invisible friend.

Offline moodnacreek

  • Senior Member x2
  • *****
  • Posts: 1958
  • Location: Orange County NY
  • Gender: Male
  • Sawin by the notches
    • Share Post
Re: Edger
« Reply #11 on: August 14, 2019, 08:15:27 AM »
Feed rolls must be parallel with arbor. Any thing on the out feed that drags on  one edge of the board will start a curve.  Also a piece of bark, pitch, etc. caught in a feed roll will do the same. Even an out feed dead roll that is not parallel or high on one side ditto. There are many things; a big knot, one saw very dull, boards too hard or too thick for the feed speed or power . If machine has a small dia. mandrel it will vibrate in tough cuts and shake the board and curve.  A guide light set on the fixed saw is a great help.

Offline Ron Wenrich

  • Forester
  • Administrator
  • *****
  • Posts: 14095
  • Age: 71
  • Location: Jonestown, PA
  • Gender: Male
    • Share Post
Re: Edger
« Reply #12 on: August 14, 2019, 05:44:00 PM »
Have you changed teeth in the edger blades yet?  I've found that you have to eliminate the problems of other people's saw maintenance practices first.  New teeth will tell you whether its in the saws or in the rolls.
Never under estimate the power of stupid people in large groups.


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
edger

Started by jdw on Norwood Sawmills USA Inc.

0 Replies
1578 Views
Last post February 04, 2016, 12:28:24 AM
by jdw
xx
looking for a edger

Started by j napier on Wanted

2 Replies
688 Views
Last post September 19, 2013, 06:04:23 AM
by j napier
xx
Edger 802

Started by J_T on Sawmills and Milling

8 Replies
2010 Views
Last post November 16, 2003, 09:50:38 AM
by UNCLEBUCK
xx
Edger

Started by Rick-Wi on Sawmills and Milling

16 Replies
5344 Views
Last post May 12, 2002, 07:38:44 AM
by ElectricAl
 


Powered by EzPortal