The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

FARMA


Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems

Tally-I/O




Author Topic: LT40 Simple Set Question  (Read 276 times)

0 Members and 1 Guest are viewing this topic.

Offline Poquo

  • member
  • *
  • Posts: 46
  • Age: 58
  • Location: Poquoson , Va
  • Gender: Male
    • Share Post
LT40 Simple Set Question
« on: September 15, 2019, 09:12:29 AM »
I noticed when using simple set the head would go down a little bit past the set point then up to right place , is this normal ?
2015 Woodmizer LT40HD26

Online Bruno of NH

  • Senior Member x2
  • *****
  • Posts: 3494
  • Age: 53
  • Location: Springfield NH
  • Gender: Male
    • Share Post
Re: LT40 Simple Set Question
« Reply #1 on: September 15, 2019, 10:01:51 AM »
Yes
I have a new mill and that's how mine works
Lt 40 wide with 38hp gas and command controls Riehl Steel edger,F350 4x4 dump and lot of contracting tools

Offline Poquo

  • member
  • *
  • Posts: 46
  • Age: 58
  • Location: Poquoson , Va
  • Gender: Male
    • Share Post
Re: LT40 Simple Set Question
« Reply #2 on: September 15, 2019, 10:17:02 AM »
Thanks Bruno mine is used with 400 hours .
2015 Woodmizer LT40HD26

Offline Percy

  • Senior Member x2
  • *****
  • Posts: 2232
  • Age: 65
  • Location: Terrace B.C. Canada
  • Gender: Male
  • Resident trouble maker
    • Share Post
Re: LT40 Simple Set Question
« Reply #3 on: September 15, 2019, 10:43:51 AM »
My accuset 2 does the same thing..coming "up" to the target mark is more accurate Im told, than coming "down" to the mark. Like tuning a guitar string... ;D
GOLDEN RULE : The guy with the gold, makes the rules.

Offline Bandmill Bandit

  • Senior Member x2
  • *****
  • Posts: 2154
  • Age: 63
  • Location: Ponoka Alberta, Canada
  • Gender: Male
    • Share Post
Re: LT40 Simple Set Question
« Reply #4 on: September 15, 2019, 10:44:19 AM »
The reason for the "bump up" is to ensure the lift chain ABOVE the head is as tight as possible. You need to do the same when you do a manual set as well. Otherwise the head will drop slightly when you engage the clutch to start your cut.
If you ain't livin on the edge you are takin up way to much room. Of course at my age if I get too close to that edge any more theres a good chance I may fall off.
2001 Dodge 1500 4x4. 2018 F150
2007 Woodmizer LT40HDG28 almost Super
2 Logrite 36 inch cant hooks and a bunch of stuff I built myself

Offline Poquo

  • member
  • *
  • Posts: 46
  • Age: 58
  • Location: Poquoson , Va
  • Gender: Male
    • Share Post
Re: LT40 Simple Set Question
« Reply #5 on: September 15, 2019, 05:51:26 PM »
Thanks for all the help , just wanted to make sure I didn't need to adjust it .
2015 Woodmizer LT40HD26


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
LT40 Simple Set

Started by ncsawyer on Sawmills and Milling

10 Replies
1263 Views
Last post March 24, 2016, 05:27:14 PM
by Solomon
xx
Simple Question

Started by grassfed on Forestry and Logging

9 Replies
1714 Views
Last post April 07, 2011, 07:47:46 PM
by Ron Scott
xx
Simple question.

Started by hackberry jake on Sawmills and Milling

20 Replies
2947 Views
Last post March 11, 2012, 03:21:18 PM
by jim blodgett
xx
Question about Simple Set on my LT35

Started by Ruffneck on Sawmills and Milling

6 Replies
888 Views
Last post April 12, 2013, 04:43:36 PM
by Ruffneck
 


Powered by EzPortal