The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

FARMA


Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems

Chainsawr, The Worlds Largest Inventory of Chainsaw Parts





Author Topic: Oops!  (Read 2088 times)

0 Members and 1 Guest are viewing this topic.

Offline Magicman

  • Senior Member x2
  • *****
  • Posts: 39459
  • Age: 76
  • Location: Brookhaven, MS
  • Gender: Male
  • A "Traveling Man"
    • Share Post
    • Knothole Sawmill
Re: Oops!
« Reply #40 on: November 01, 2019, 08:21:19 AM »
I will say this; if that truck door stays open, the inside will get sawdust.  :o   Same as if a window in left open.  :-X
Knothole Sawmill, LLC     '98 Wood-Mizer LT40SuperHydraulic   WM Million BF Club Member   WM Pro Sawyer Network

Never allow your "need" to make money to exceed your "desire" to provide quality service.....The Magicman

Offline Stephen1

  • Senior Member x2
  • *****
  • Posts: 1775
  • Age: 64
  • Location: Kilworthy ON> Canada
  • Gender: Male
  • Where there is a will, there is a way!
    • Share Post
    • muskoka Sawmill
Re: Oops!
« Reply #41 on: November 01, 2019, 08:32:10 AM »
I have doen it where it took a few hours to hand lift it back up at a customers,, no heavy equipment to lift it with. The last thing I do after I saw the last board is lift the back stops, move the clamp all the way out, then I shut down the mill aand move lumber and load a log on th arms.
IDRY Vacum Kiln, LT40HDWide, BMS250 sharpener/setter 742b Bobcat, TCM forklift, Sthil 026,038, 461. 1952 TEA Fergusan Tractor

Offline Banjo picker

  • Senior Member x2
  • *****
  • Posts: 2924
  • Location: Iuka Ms
  • Gender: Male
    • Share Post
Re: Oops!
« Reply #42 on: November 01, 2019, 01:28:05 PM »
That is the reason that if you have an energy chain (gooseneck) with your hydraulic lines in it... you always bring the mill back before you roll a log or cant.  Banjo
Never explain, your friends don't need it, and your enemies won't believe you any way.

Offline SawyerTed

  • Senior Member x2
  • *****
  • Posts: 1333
  • Age: 57
  • Location: Germanton, NC
  • Gender: Male
  • Summey Lumber Services, LLC
    • Share Post
Re: Oops!
« Reply #43 on: November 01, 2019, 07:32:43 PM »
My wife's cousin had me come to the home place of their grandparents to saw some 32" red oak logs.  Yep, rolled one over the back stops and off the mill.  No equipment to get the log back in place so I had to break the mill down and turn it around to get the log.  I was sawing the lumber for family (aka free of charge) so the time didn't matter.
Woodmizer LT35HD25, Kubota MX5100, IH McCormick Farmall 140, Granberg Alaskan Chainsaw Mill, Husqvarna 372XP, Husqvarna 455 Rancher, Ram 3500 6.7 Cummins

Offline Stephen1

  • Senior Member x2
  • *****
  • Posts: 1775
  • Age: 64
  • Location: Kilworthy ON> Canada
  • Gender: Male
  • Where there is a will, there is a way!
    • Share Post
    • muskoka Sawmill
Re: Oops!
« Reply #44 on: November 02, 2019, 08:33:07 AM »
My wife's cousin had me come to the home place of their grandparents to saw some 32" red oak logs.  Yep, rolled one over the back stops and off the mill.  No equipment to get the log back in place so I had to break the mill down and turn it around to get the log.  I was sawing the lumber for family (aka free of charge) so the time didn't matter.
On the WM they get stuck between the frame and the tire, not a good spot as you have to lift them out
IDRY Vacum Kiln, LT40HDWide, BMS250 sharpener/setter 742b Bobcat, TCM forklift, Sthil 026,038, 461. 1952 TEA Fergusan Tractor

Offline samandothers

  • Senior Member x2
  • *****
  • Posts: 3059
  • Location: Charlotte NC To SW Va.
  • Gender: Male
  • Been learning on FF since 1/20/12
    • Share Post
Re: Oops!
« Reply #45 on: November 02, 2019, 10:07:30 AM »
I just did this yesterday demonstrating the log loading process to my step son. No pics but I got to cross that off the list
I am sure you immediately shared this is to show what not to do and is part of the demonstration.


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
Oops

Started by Bill Gaiche on Sawmills and Milling

37 Replies
5140 Views
Last post October 12, 2011, 07:22:45 PM
by zopi
xx
OOPS

Started by sawman on Sawmills and Milling

39 Replies
7392 Views
Last post December 31, 2003, 02:46:04 PM
by Wes
xx
oops!

Started by Den Socling on General Board

14 Replies
804 Views
Last post April 03, 2014, 10:48:44 AM
by Raider Bill
xx
oops!

Started by woodmills1 on General Board

6 Replies
1497 Views
Last post January 21, 2010, 06:15:31 PM
by woodmills1
 


Powered by EzPortal