The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems

Chainsawr, The Worlds Largest Inventory of Chainsaw Parts





Author Topic: LT 40 Super or LT50 Woodmizer.  (Read 1716 times)

0 Members and 1 Guest are viewing this topic.

Offline terrifictimbersllc

  • Senior Member x2
  • *****
  • Posts: 5061
  • Age: 66
  • Location: Mystic, CT
  • Gender: Male
    • Share Post
    • Terrific Timbers LLC
Re: LT 40 Super or LT50 Woodmizer.
« Reply #40 on: February 03, 2020, 04:47:49 AM »
It's 55HP Yanmar same as mine.
DJ Hoover, Terrific Timbers LLC,  Mystic CT Woodmizer Million Board Foot Club member. 2019 LT70 Super Wide 55 Yanmar,  LogRite fetching arch, WM BMS250 sharpener/BMT250 setter.  2001 F350 7.3L PSD 6 spd manual ZF 4x4 Crew Cab Long Bed

Offline YellowHammer

  • Senior Member x2
  • *****
  • Posts: 4952
  • Age: 55
  • Location: New Market, Alabama
  • Gender: Male
  • Take Steps to Save Steps
    • Share Post
    • Hobby Hardwood Alabama
Re: LT 40 Super or LT50 Woodmizer.
« Reply #41 on: February 03, 2020, 07:50:27 AM »
Here is a video on of our Forum members made after he got his LT70.  It cuts pretty fast.  There's not a lot of time for cruise control while in the cut.


HobbyHardwoodAlabama.com

Offline Magicman

  • Senior Member x2
  • *****
  • Posts: 39857
  • Age: 76
  • Location: Brookhaven, MS
  • Gender: Male
  • A "Traveling Man"
    • Share Post
    • Knothole Sawmill
Re: LT 40 Super or LT50 Woodmizer.
« Reply #42 on: February 03, 2020, 08:24:13 AM »
Just as a note in case you are wondering, his cants are bucked and then go through a resaw for pallet lumber.  It's a specialty situation and is not a normal sawing pattern nor sequence for lumber.  Ultimately he needed an even faster sawmill to meet his need. 
Knothole Sawmill, LLC     '98 Wood-Mizer LT40SuperHydraulic   WM Million BF Club Member   WM Pro Sawyer Network

Never allow your "need" to make money to exceed your "desire" to provide quality service.....The Magicman

Offline PAmizerman

  • Senior Member
  • ****
  • Posts: 674
  • Age: 28
  • Location: Loretto PA
  • Gender: Male
  • Just Another Day In Paradise!!
    • Share Post
    • Byrne Millwork
Re: LT 40 Super or LT50 Woodmizer.
« Reply #43 on: February 03, 2020, 08:49:37 PM »
Yeah I'm familiar with 4x4 setup.
Woodmizer lt40 super remote 42hp Kubota diesel. Accuset II
Hydraulics everywhere
Woodmizer edger 26hp cat diesel
Traverse 6035 telehandler
Case 95xt skidloader
http://byrnemillwork.com/
WM bms250 sharpener
WM bmt250 setter
and a lot of back breaking work!!

Offline boonesyard

  • Full Member x2
  • ***
  • Posts: 242
  • Age: 61
  • Location: Wolverton, MN
  • Gender: Male
  • I've got a little sawdust in my pocket
    • Share Post
Re: LT 40 Super or LT50 Woodmizer.
« Reply #44 on: February 04, 2020, 10:17:32 AM »


I can't speak for the LT40, but the dragback guide fingers are not available for the LT40 unless you add them yourself.   The WM set made for the LT70 does not fit directly.  It requires modification.    I installed them on my mill a few months ago.
My drag back fingers will be here tomorrow. I spoke with Wood-Mizer a few times on building mine to be specific for the 40. Tomorrow I will find out how they did.
Nathan,
Did WM have a fingers solution for your LT40, or are they customizing something for you? If they have put something together, I would like to check on that for my 50. 
LT50 wide
iDRY Standard kiln
JD 4520 w/FEL
lots of support equipment and not enough time

"I ain't here for a long time, I'm here for a good time"


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
Converting an LT40 Super to an LT50.

Started by Dave Shepard on Sawmills and Milling

20 Replies
3617 Views
Last post January 31, 2020, 03:36:42 PM
by Bandmill Bandit
question
hydraulic flow for WM LT50 vs LT40 super

Started by bonecutter on Sawmills and Milling

4 Replies
413 Views
Last post March 02, 2019, 04:53:39 PM
by bonecutter
xx
GVWR of Woodmizer LT50

Started by jeepcj779 on Sawmills and Milling

8 Replies
423 Views
Last post February 09, 2020, 04:28:08 PM
by E-Tex
xx
2016 Woodmizer LT50

Started by Seavee on For Sale

9 Replies
15160 Views
Last post September 03, 2019, 10:59:41 PM
by Kristen24060
 


Powered by EzPortal