The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems

Chainsawr, The Worlds Largest Inventory of Chainsaw Parts

Smith Sawmill Service

Dynamic Green Products Inc.





Author Topic: 394xp or 2095 Jonsered  (Read 2281 times)

0 Members and 1 Guest are viewing this topic.

Offline mcourtney

  • member
  • *
  • Posts: 22
  • Age: 53
  • Location: Pomme De Terre
  • Gender: Male
    • Share Post
394xp or 2095 Jonsered
« on: January 09, 2014, 09:06:19 PM »
I have a 394xp and found a 2095 Jonsered close to home worth the money , whats the internal differences between them.

Offline weimedog

  • Senior Member x2
  • *****
  • Posts: 1362
  • Location: CNY
  • Gender: Male
  • Better to be a "Has Been" than a "Never Been"!
    • Share Post
Re: 394xp or 2095 Jonsered
« Reply #1 on: January 10, 2014, 12:22:19 AM »
They can use the same piston..... ::)  I could be wrong, but Don't think much else is the same. The 2094 is one nasty saw when setup right. Better have good ear protection! The 2095 is more useful because it has a compression release so you don't either break your pull start or rip your fingers off pulling that monster over!
Husqvarna 365sp/372xpw Blend, Jonsered 2171 51.4mm XPW build,562xp HTSS, 560 HTSS, 272XP, 61/272XP, 555, 257, 242, 238, Homelite S-XL 925, XP-1020A, Super XL (Dad's saw); Jonsered 2094, Three 920's, CS-2172, Solo 603; 3 Huztl MS660's (2 54mm and 1 56mm)

Offline SawTroll

  • Senior Member x2
  • *****
  • Posts: 2468
  • Age: 63
  • Location: Troms, North Norway
  • Gender: Male
    • Share Post
Re: 394xp or 2095 Jonsered
« Reply #2 on: January 10, 2014, 09:45:45 AM »
Yes, they are very different designs, that share very little - although the bore and stroke is the same.

That's a bit funny really, as both were made (partially) at the same time, at the same factory (Husky factory in Sweden).  8)
Information collector.

Offline Timberjack_395XP

  • Full Member
  • **
  • Posts: 61
  • Age: 38
  • Location: Indiana
  • Gender: Male
  • I love this place!
    • Share Post
Re: 394xp or 2095 Jonsered
« Reply #3 on: February 13, 2014, 03:19:22 PM »
My 394xp has a compression release on it

Offline Spike60

  • Senior Member
  • ****
  • Posts: 497
  • Location: Ulster County, NY
    • Share Post
Re: 394xp or 2095 Jonsered
« Reply #4 on: February 13, 2014, 03:35:25 PM »
They also use the same crankshaft, but little else will interchange.

All 394's and 395's had the compression release as did the 2095. It was only the 2094 that didn't. Can't imagine why they brought that saw out without one.  ???
Husqvarna-Jonsered
Ashokan Turf and Timber
845-657-6395

Offline Maine logger88

  • Senior Member x2
  • *****
  • Posts: 1912
  • Age: 32
  • Location: Morrill ME
  • Gender: Male
  • Don't force it get a bigger hammer
    • Share Post
Re: 394xp or 2095 Jonsered
« Reply #5 on: February 13, 2014, 07:11:49 PM »
I wonder why jonsered dropped the 95cc saws?
79 TJ 225 81 JD 540B Husky and Jonsered saws


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
Jonsered 2095

Started by saw_nut on Wanted

0 Replies
1093 Views
Last post May 05, 2009, 04:13:01 PM
by saw_nut
xx
How is a Jonsered 2095 for milling?

Started by nk14zp on Sawmills and Milling

1 Replies
709 Views
Last post December 01, 2013, 01:01:12 PM
by sawguy21
xx
looking to buy jonsered 2095 and husqvarna 288xp

Started by recurve60 on For Sale

1 Replies
837 Views
Last post November 27, 2019, 12:19:13 PM
by moosehunter
xx
Ripping bar-chain For 2095

Started by Lenny_M on Chainsaws

1 Replies
1085 Views
Last post February 15, 2004, 06:04:31 AM
by Kevin
 


Powered by EzPortal