The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems

Chainsawr, The Worlds Largest Inventory of Chainsaw Parts





Author Topic: porting an 044  (Read 4808 times)

0 Members and 1 Guest are viewing this topic.

Offline charleswalton

  • member
  • *
  • Posts: 18
  • Location: Dallas,Ga.
  • Gender: Male
    • Share Post
Re: porting an 044
« Reply #20 on: January 16, 2014, 11:39:50 AM »
How do you measure squish?

Offline Al_Smith

  • Senior Member x2
  • *****
  • Posts: 10614
  • Location: Northwestern Ohio in the center of a giant corn field
  • Gender: Male
    • Share Post
Re: porting an 044
« Reply #21 on: January 16, 2014, 12:44:02 PM »
You put 4 pieces of soft solder on top of the piston .Two in the center over of the rod and two dead center at a right angle .Roll the piston over to smash the solder then use a set of micrometers to measure the smashed solder .Use as thin of solder as will just be smashed not something like heavy 50/50 body solder.

You can buy it in 62 thou rosin core which mashs fairly easy .I'd probabley avoid acid core myself .Solid would work if you can find it small enough .

Offline Al_Smith

  • Senior Member x2
  • *****
  • Posts: 10614
  • Location: Northwestern Ohio in the center of a giant corn field
  • Gender: Male
    • Share Post
Re: porting an 044
« Reply #22 on: January 16, 2014, 12:46:22 PM »
When I said dead center I meant towards the outside of the piston not center of the piston .All that would do is shove it up into the combustion chamber .

Offline charleswalton

  • member
  • *
  • Posts: 18
  • Location: Dallas,Ga.
  • Gender: Male
    • Share Post
Re: porting an 044
« Reply #23 on: January 17, 2014, 07:40:45 AM »
Thanks everyone for the advise.


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

smiley
359 porting

Started by nuke1 on Chainsaws

15 Replies
3119 Views
Last post November 27, 2015, 12:24:44 PM
by ehp
xx
porting

Started by oakwood productions on Chainsaws

22 Replies
6075 Views
Last post May 30, 2009, 11:53:05 AM
by Cut4fun
xx
thinking about porting my 385

Started by woodtick#2 on Chainsaws

20 Replies
3861 Views
Last post August 02, 2012, 01:01:07 PM
by Al_Smith
xx
porting and muffler add ons?

Started by symamania on Chainsaws

6 Replies
1651 Views
Last post June 21, 2015, 11:20:02 AM
by HolmenTree
 


Powered by EzPortal