The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems

Chainsawr, The Worlds Largest Inventory of Chainsaw Parts





Author Topic: can somone tell me how to change the oil line on my 266 xp ?  (Read 485 times)

0 Members and 1 Guest are viewing this topic.

Offline treechopper40

  • Full Member x2
  • ***
  • Posts: 121
  • Location: upstate new york
  • Gender: Male
  • cut it skid it load it truck it
    • Share Post
can somone tell me how to change the oil line on my 266 xp ?
« on: February 01, 2014, 09:10:56 PM »
hi do I need to split the cases to change the oil line on my 266 husky or is there another way please help
1979 c5d treefarmer 1966 c5b treefarmer prentice g model loader 2 6100 dolmars a 6400 dolmar and a 7910 dolmar 2012 ford f 250 4x4 with a service body and 2 golden retreivers

Offline AKDoug

  • Full Member
  • **
  • Posts: 62
  • Age: 51
  • Location: Alaska
    • Share Post
Re: can somone tell me how to change the oil line on my 266 xp ?
« Reply #1 on: February 02, 2014, 02:18:15 AM »
It connects to the oil pump and passes through the wall into the oil tank. It is replaceable without splitting the case.

Online sablatnic

  • Senior Member
  • ****
  • Posts: 598
  • Location: Denmark
  • Gender: Male
    • Share Post
Re: can somone tell me how to change the oil line on my 266 xp ?
« Reply #2 on: February 02, 2014, 03:59:02 AM »
Just remove the clutch and the oil pump, and there you are, it's the round rubber thing.
And while the pump is out, take a look at the crank shaft seal, if it is worn, replace it, and replace the one in the other side too, as it most likely has run just as many hours.

Offline NCFarmboy

  • Senior Member
  • ****
  • Posts: 258
  • Age: 72
  • Location: Hayesville, NC 28904
  • Gender: Male
    • Share Post
Re: can somone tell me how to change the oil line on my 266 xp ?
« Reply #3 on: February 02, 2014, 07:39:30 AM »
Just remove the clutch and the oil pump, and there you are, it's the round rubber thing.
And while the pump is out, take a look at the crank shaft seal, if it is worn, replace it, and replace the one in the other side too, as it most likely has run just as many hours.
Very good advice.  I would replace seal and O-ring while I had oil pump off.  Cheap insurance.
Shep
Lots & Lots of Saws


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
What are the significant change years to the LT40 Line of Woodmizers?

Started by MikeySP on Sawmills and Milling

6 Replies
413 Views
Last post January 27, 2019, 05:54:18 PM
by uler3161
xx
this might interest somone

Started by sawhead on Sawmills and Milling

2 Replies
1179 Views
Last post January 14, 2004, 07:56:22 PM
by Jeff
xx
Change band brands...change tracking?

Started by kelLOGg on Sawmills and Milling

24 Replies
2075 Views
Last post July 21, 2014, 05:56:28 PM
by ladylake
xx
I dug thorugh the electric line, phone, and water line

Started by ozarkgem on General Board

25 Replies
2167 Views
Last post April 20, 2015, 08:41:07 PM
by ozarkgem
 


Powered by EzPortal