The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

FARMA


Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems

Chainsawr, The Worlds Largest Inventory of Chainsaw Parts





Author Topic: Remove walbro carb screw limiters  (Read 2074 times)

0 Members and 1 Guest are viewing this topic.

Offline 7sleeper

  • Full Member x2
  • ***
  • Posts: 242
  • Location: Austria
  • Gender: Male
  • I'm new here but old elsewhere!
    • Share Post
Remove walbro carb screw limiters
« on: February 03, 2014, 02:17:22 PM »
Dear community,

I have searched this forum and haven't found any info on the topic of this type of carb cap. I have also searched other forums but haven't found what I am looking for.

I am aware of using a dry wall screw to remove the "epa" caps but this model is more than resilient. It is on a walbro carb and I would like to remove it in a way as to reapply after correction. If I pull it I can only get it off 1-2mm. That's all. After that it just snaps in place and I could hang the saw from the limiter!
Any one an idea?

Here is a pic from the outside.




Thanks for the help!

7

p.s. it's about this saw


<iframe width="650" height="385" src="//www.youtube.com/embed/CimuajB4Vq4?fs=1&start=" frameborder="0" allowfullscreen></iframe>

Offline Andyshine77

  • Senior Member
  • ****
  • Posts: 678
  • Age: 42
  • Location: Cincinnati, OH
  • Gender: Male
    • Share Post
Re: Remove walbro carb screw limiters
« Reply #1 on: February 03, 2014, 03:38:52 PM »
All you have to do with those is grind or clip the plastic lobes off. You may have to remove the cover or carb to do so.
Andre.

Offline weimedog

  • Senior Member x2
  • *****
  • Posts: 1322
  • Location: CNY
  • Gender: Male
  • Better to be a "Has Been" than a "Never Been"!
    • Share Post
Re: Remove walbro carb screw limiters
« Reply #2 on: February 03, 2014, 03:40:51 PM »
Nippers for the plastic, then dremel  tool that little stem off ("cut off wheel") back so the "spline" is accessible to the carb adjustment tool .. essentially a spline drive about the size of a screw driver
Husqvarna 365sp/372xpw Blend, Jonsered 2171 51.4mm XPW build,562xp HTSS, 560 HTSS, 272XP, 61/272XP, 555, 257, 242, 238, Homelite S-XL 925, XP-1020A, Super XL (Dad's saw); Jonsered 2094, Three 920's, CS-2172, Solo 603; 3 Huztl MS660's (2 54mm and 1 56mm)

Offline 7sleeper

  • Full Member x2
  • ***
  • Posts: 242
  • Location: Austria
  • Gender: Male
  • I'm new here but old elsewhere!
    • Share Post
Re: Remove walbro carb screw limiters
« Reply #3 on: February 03, 2014, 04:11:36 PM »
Thanks will try and report back.

7


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
Stihl Carb Limiters

Started by Dixiebonsai on Chainsaws

2 Replies
759 Views
Last post December 16, 2015, 08:35:15 PM
by Texas-Jim
xx
Need Help..........Walbro Carb!!!

Started by rahtreelimbs on Chainsaws

2 Replies
1364 Views
Last post August 23, 2005, 08:51:38 AM
by woodbowl
xx
Walbro HD-17A carb replacement

Started by pwheel on Chainsaws

0 Replies
546 Views
Last post September 01, 2015, 10:55:53 AM
by pwheel
question
echo cs 680 walbro hda 271 carb

Started by vladislav95 on Chainsaws

8 Replies
2531 Views
Last post May 20, 2015, 12:06:02 PM
by SlimJim
 


Powered by EzPortal