Author Topic: Please welcome Turbosawmill (Read 4832 times)

Jeff · « **on:** February 04, 2015, 04:20:47 PM »

Its about time Jake! Welcome!

Long time member Jake Peterson @NZJake and his Turbosawmill are now sponsors of the Forestry Forum!

Please take the time to check out some of the newest and cleverest innovations in swingmill sawmills at his website, and be sure to keep track of him down on his new Turbosawmill sponsor board in the Sponsor board section of the Forestry Forum.

POSTON WIDEHEAD · « **Reply #1 on:** February 04, 2015, 04:41:52 PM »

I haven't had time to look at your website yet but I do have the time to Welcome you to the Forestry Forum as a Sponsor.
This is great.

Love the Logo.

Chuck White · « **Reply #2 on:** February 04, 2015, 04:46:55 PM »

Thank you for sponsoring the Forestry Forum, Jake!

I see you've been a member here since 2004, congratulations!

sprucebunny · « **Reply #3 on:** February 04, 2015, 05:01:14 PM »

Thanks for being a sponsor, Jake

Those sawmills look very innovative.

thecfarm · « **Reply #4 on:** February 04, 2015, 07:28:35 PM »

Welcome. Coming to the expo in Bangor,Maine in May???

http://nefpexpo.net/

Magicman · « **Reply #5 on:** February 04, 2015, 07:49:22 PM »

Thank you for your Forestry Forum Sponsorship Jake. Welcome Turbosawmill

dgdrls · « **Reply #6 on:** February 04, 2015, 07:56:40 PM »

Thank-you for being on the Board as a supporting sponsor

best DGDrls

Ga Mtn Man · « **Reply #7 on:** February 04, 2015, 08:17:52 PM »

Welcome and thanks to TurboSawmill for sponsoring our favorite place to hang out.

WDH · « **Reply #8 on:** February 04, 2015, 08:27:20 PM »

Welcome Jake and thanks for your support.

Peter Drouin · « **Reply #9 on:** February 04, 2015, 09:47:50 PM »

Hi,

And welcome.

NZJake · « **Reply #10 on:** February 06, 2015, 02:20:54 AM »

Thanks for the welcome guys. Thecfarm... not sure yet regarding Maine. Just taking it bit by bit at the moment. My schedule is pretty busy right now commissioning our larger Gladiator mills.

Would love to attend the shoot out so will try and put some targets up for that one!

SwampDonkey · « **Reply #11 on:** February 06, 2015, 04:35:45 AM »

Welcome a board. Yep, that usually means we like sawmillers and the fellows with the innovation and expertise to make their mills. And especially ones that stand behind them.

Just Me · « **Reply #12 on:** February 07, 2015, 07:49:05 AM »

I told my wife to win the lottery, but as usual she does not pay a lot of attention to me. If she ever does what I tell her to you will be one of my first calls. I want to play.....

Welcome

fat olde elf · « **Reply #13 on:** February 09, 2015, 12:12:04 AM »

Thanks for supporting the Forum. Saw videos of your equipment,sure looks interesting.
Thanks again.....

Hilltop366 · « **Reply #14 on:** February 09, 2015, 09:12:30 AM »

Thanks Jake!

customsawyer · « **Reply #15 on:** February 13, 2015, 04:47:26 AM »

Thanks for your support.

Weekend_Sawyer · « **Reply #16 on:** February 14, 2015, 03:16:33 PM »

Welcome and thanks for being a sponsor. How do you feel about Goats?

NZJake · « **Reply #17 on:** February 16, 2015, 03:03:51 AM »

They are ok.

NZJake · « **Reply #18 on:** February 16, 2015, 03:11:28 AM »

Thanks all for welcoming us! Hopefully we can stay long term. Maybe even get to meet some of you.

Cheers.
Jake.

fishinbill85 · « **Reply #19 on:** March 27, 2015, 08:41:09 PM »

Hello all, new to the forum and sawmilling! I just read the thread on "acceptable beam sag" for the TurboSawmill Weekend Warrior and felt compelled to post my experiences and thoughts about the mill, and pose a question or two for Jake.

First off, I purchased an 8" CS weekend warrior in August of 2014. I'll spare the details, but the process of actually getting the mill was... not good. (Shipping and customs) Upon the mill arriving, (the first time) I pointed out MY concerns with some quality control issues that I felt could be improved upon to Mike (TSM USA) and Jake. Basically, all issues were taken care of at ZERO cost to me and to my satisfaction 100%! It did take awhile to get them resolved (I received my mill this February 2015), but hey, things take time, especially when I am literally on the other side of the planet! Jake called me several times on my cell to ask questions and clarify things that got mixed up in the pipeline. Kudos to Jake and Mike on that!

Now, after I finally got the sawmill assembled and adjusted, I too noticed that the beam (mine is split in the middle with the inserts) had some sag to it, but not excessive. I would venture to guess 3-5 mil? I tried and tried according to Mike's instruction to get it straighter, but it wouldn't stay after the mill head passed over the center a few times under load, it would go back to that 3-5 mil zone. When I sawed an 18' pine for a friend, I added the extension to the end and the sag went to close to 12-15 mil in the center of the beam. I don't know about the rest of you, but I know I want the straightest lumber I can get to minimize having to dress it up after the fact. I checked the boards coming off the log and while they do have some "cup" over the length of the log... they are the same thickness and dimension's over all, board to board, and 100% square. Personally, I don't think I'll use it in it's longest configuration very often, so I believe the "cup" will be minimized on shorter boards with the standard beam sections. It just takes some getting use to... The mill and the lumber. All in all, it's well thought out but could use some polishing...which Jake is constantly doing btw.

Did I read in the other thread Jake, that you could put a crown on the inserts to make the beam bow up just a tad? How would I go about doing that safely without kinking the tubes? I think that would work perfect for what I need.

Once again, a big thanks to TurboSawmill, Mike, and NZJake for making an innovative sawmill and backing it up with great customer service!

P.S. The brackets worked fine for the carriage.

Looking forward to learning from everybody here and making some sawdust!

Forestry ForumSponsored by:

Author Topic: Please welcome Turbosawmill (Read 4832 times)

Forestry Forum
Sponsored by: