The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems

Chainsawr, The Worlds Largest Inventory of Chainsaw Parts





Author Topic: 1400 CB solenoid sticking  (Read 552 times)

0 Members and 1 Guest are viewing this topic.

Offline overclocking

  • Full Member x2
  • ***
  • Posts: 126
  • Location: Upstate, NY
  • Gender: Male
  • I'm new!
    • Share Post
1400 CB solenoid sticking
« on: October 07, 2016, 10:26:39 PM »
I have a CB 1400, the Solo for the low side is sticking and causing it to burn wood faster then normal. I cleaned it,it still stuck so I replaced it. New one does the same thing after a week. I slam the door or bang on the side and I can hear it close. I don't want this to overheat or waste wood, should I put some weights on it or a small bungy cord to pull it down a little? Anyone else ever see this?

Offline Wood Shed

  • Full Member x2
  • ***
  • Posts: 114
  • Age: 66
  • Location: North Central Ohio
  • Gender: Male
  • Retired antique tractor guy enjoying my Tree Farm
    • Share Post
Re: 1400 CB solenoid sticking
« Reply #1 on: October 14, 2016, 08:29:21 AM »
I have a different model of CB and have not seen the problem you are but this year has been frustrating.  I knew the minute it was powered up something had changed (sits idle all summer).  The controller was acting erratically posting wide temp fluctuations.  So I threw $50 at it installing a new controller, did the same thing.  While working on it I noticed it went on and off if I bumped the ground wire.  Cleaned and repaired the ground connection, now I have an extra control module.  So, check your ground.  HTH
A society grows great when old men plant trees whose shade they know they shall never sit in. -Greek Proverb

Offline davewittwer

  • member
  • *
  • Posts: 16
  • Location: MN
  • Gender: Male
    • Share Post
Re: 1400 CB solenoid sticking
« Reply #2 on: October 19, 2016, 04:14:39 PM »
I had an issue with a sticky solenoid last year.  Cleaned with WD40 and worked great.  I also have had some issues with the wiring that controls the solenoid.  Re did some of that this fall, hopefully that will cure the problem when i fire the stove up.  Good luck, let us know what you come up with.

Offline OneWithWood

  • Senior Member x2
  • *****
  • Posts: 5680
  • Age: 66
  • Location: Unionville, IN
  • Gender: Male
  • I am happy!
    • Share Post
Re: 1400 CB solenoid sticking
« Reply #3 on: October 22, 2016, 11:05:00 AM »
Check the alignment of the actuator linkage.
One With Wood
LT40HDG25, Woodmizer DH4000 Kiln


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

xx
CB e2400 Solenoid sticking

Started by mojamboo on Firewood and Wood Heating

11 Replies
2080 Views
Last post January 27, 2015, 02:28:09 PM
by ohiowoodchuck
xx
Sticking chainsaws

Started by Weekend_Sawyer on General Board

16 Replies
918 Views
Last post March 31, 2014, 09:39:21 PM
by Philbert
xx
STICKING TO THE OLE WAYS

Started by Tom_in_Mo. on General Board

12 Replies
1054 Views
Last post August 07, 2004, 03:15:56 PM
by rebocardo
xx
saw dust sticking

Started by fivedogs on Sawmills and Milling

15 Replies
4794 Views
Last post December 27, 2011, 11:57:03 PM
by never finished
 


Powered by EzPortal