The Forestry Forum is sponsored in part by:

iDRY Vacuum Kilns


Forestry Forum
Sponsored by:


TimberKing Sawmills



Toll Free 1-800-582-0470

LogRite Tools



Norwood Industries Inc.




Your source for Portable Sawmills, Edgers, Resaws, Sharpeners, Setters, Bandsaw Blades and Sawmill Parts

EZ Boardwalk Sawmills. More Saw For Less Money!

STIHLDealers.com sponsored by Northeast STIHL


Woodland Sawmills

Peterson Swingmills

 KASCO SharpTech WoodMaxx Blades

Turbosawmill

Sawmill Exchange

Michigan Firewood, your BRUTE FORCE Authorized Dealer

FARMA


Baker Products

ECHO-Bearcat

iDRY Wood Lumber Vacuum Drying for everyon

Nyle Kiln Dry Systems

Chainsawr, The Worlds Largest Inventory of Chainsaw Parts





Author Topic: Kiln fan  (Read 461 times)

0 Members and 1 Guest are viewing this topic.

Offline xlogger

  • Senior Member x2
  • *****
  • Posts: 1401
  • Age: 66
  • Location: Bahama, NC
  • Gender: Male
    • Share Post
Kiln fan
« on: September 02, 2017, 12:29:24 PM »
My fan in the kin sounds like what Danny has been telling me for awhile now. One of the fans in the unit sounds like it's loose. I guess I'll be ordering one after the holidays.  Maybe I will go ahead and take it out and replace with one of the extra 4 fans I put in the kiln till the new one gets here.  That way I can keep running the kiln. The extra ones are simple to install.
Timberking 2000, Turbo slabber Mill, 584 Case, Bobcat 773, solar kiln, Nyle L-53 DH kiln

Offline pine

  • Senior Member
  • ****
  • Posts: 668
  • Location: PNW
    • Share Post
Re: Kiln fan
« Reply #1 on: September 02, 2017, 04:20:11 PM »
Are the fans on the L53 the same as the fans on the L200? On the Nyle site I only see the L200 and L300 fans.
Or is this the fan that is inside the unit itself?
Hope the price is not too bad.

Offline xlogger

  • Senior Member x2
  • *****
  • Posts: 1401
  • Age: 66
  • Location: Bahama, NC
  • Gender: Male
    • Share Post
Re: Kiln fan
« Reply #2 on: September 02, 2017, 04:52:32 PM »
Not sure about that but I have an outlet giving to me of a place you can get the fans, they suppose to take heat somewhat better than what came with the unit (sorry Stan). Maybe Stan will see this and have a better idea. pm me if you need it.
Just looked at their site and they say the fans are on back order.
Timberking 2000, Turbo slabber Mill, 584 Case, Bobcat 773, solar kiln, Nyle L-53 DH kiln

Offline xlogger

  • Senior Member x2
  • *****
  • Posts: 1401
  • Age: 66
  • Location: Bahama, NC
  • Gender: Male
    • Share Post
Re: Kiln fan
« Reply #3 on: September 05, 2017, 05:53:07 AM »
I took both of the fans out of the unit yesterday, one was making a pretty good noise and the other just a little louder than normal. Since I had it apart I decided on going ahead and replacing both. I rob the new fans off the shelf I built in the kiln that I had 4 extra fans on, now to order two to replace them. The two off the shelf was about 1/2 inch thicker than the ones that came with the Nyle so I had to cut a small area off one so they would fit without hitting each other. If you look at the fan on the left you can see where I had trim it back a little near the other fan.

 
Timberking 2000, Turbo slabber Mill, 584 Case, Bobcat 773, solar kiln, Nyle L-53 DH kiln

Offline WDH

  • Forester
  • Administrator
  • *****
  • Posts: 29822
  • Age: 66
  • Location: Perry, GA
  • Gender: Male
  • April 1998 - August 2008
    • Share Post
    • hamsleyhardwood.com
Re: Kiln fan
« Reply #4 on: September 05, 2017, 07:59:15 AM »
You look good to go.
Woodmizer LT40HDD35, John Deere 2155, Kubota M5640SU, Nyle L53 Dehumidification Kiln, and a passion for all things with leafs, twigs, and bark.  hamsleyhardwood.com


Share via delicious Share via digg Share via facebook Share via linkedin Share via pinterest Share via reddit Share via stumble Share via tumblr Share via twitter

 


Powered by EzPortal