iDRY Vacuum Kilns

Sponsors:

My timber frame build

Started by Ljohnsaw, April 22, 2013, 01:25:11 AM

Previous topic - Next topic

0 Members and 1 Guest are viewing this topic.

Ljohnsaw

This was from the end of March. About 7 feet left then.

The dead tree in the center, just to the left is my skytrac poking out. Way in the back is the top of my well house, 8 foot tall. So, a little melting to do still.

Warm some days in the upper 50s and freezing overnight.
John Sawicky

Just North-East of Sacramento...

SkyTrak 9038, Ford 545D FEL, Davis Little Monster backhoe, Case 16+4 Trencher, Home Built 42" capacity/36" cut Bandmill up to 54' long - using it all to build a timber frame cabin.

Stephen1

Getting there. Should almost be gone now?
IDRY Vacum Kiln, LT40HDWide, BMS250 sharpener/setter 742b Bobcat, TCM forklift, Sthil 026,038, 461. 1952 TEA Fergusan Tractor

Ljohnsaw

Wrapping up my job down here and will start hauling my equipment up next week. The "local" CalTrans camera to my property has been MIA for a couple years now, so no eyes on the snow. Supposed to be flurries Saturday just above me.
John Sawicky

Just North-East of Sacramento...

SkyTrak 9038, Ford 545D FEL, Davis Little Monster backhoe, Case 16+4 Trencher, Home Built 42" capacity/36" cut Bandmill up to 54' long - using it all to build a timber frame cabin.

TimW

Hot dog!  Lights, camera, action! ffcool
Mahindra 6520 4WD with loader/backhoe and a Caterpiller E70 Excavator.  My mill is a Woodmizer LT40HD Wide 35hp Yanmar Diesel. An old Lull 644D-34 called Bull

Ljohnsaw

A neighbor reported a burglary last week up there so my son and I flew up the hill to check things out at my place as well as others. Nothing seemed to have been touched.

There was a couple little banks of snow left. No winter damage this year 😁 A very tall dead pine that the woodpeckers had made some big holes in broke off midway up. The remaining will be much safer to drop.

Yesterday I took my mill head up and used the Ford to set it on the track. Hydraulics are nowhere near as smooth as the skytrac. But got her done.  Installed a "gravity flush" RV toilet in my bathhouse. Want to see if I like those for the cabin. Much easier to winterize.  My camp trailer pad was a bit sloped so moved 4 or 5 buckets of dirt.

Today up went the camper. Turns out there were a couple little dips on the "improved" pad that were not in sync on each side of the pad. So, by moving the trailer a little forward or back I was able to level without blocks!

I ran the well pump yesterday for a few hours and got a couple hundred gallons before a tree shaded the solar panel. When the sun came around, it didn't start back up. It didn't get hot, it's got power (through a Linear Current Booster) so not sure what's up. I think I have spare brushes if I can find them, so I'll try that Sunday or Monday.

Always something.
John Sawicky

Just North-East of Sacramento...

SkyTrak 9038, Ford 545D FEL, Davis Little Monster backhoe, Case 16+4 Trencher, Home Built 42" capacity/36" cut Bandmill up to 54' long - using it all to build a timber frame cabin.

Magicman

Maybe some glitches but it is good to see you moving again.  ffcool
Knothole Sawmill, LLC     '98 Wood-Mizer LT40SuperHydraulic   WM Million BF Club Member   WM Pro Sawyer Network

It's Weird being the Same Age as Old People

Never allow your "need" to make money to exceed your "desire" to provide quality service.....The Magicman

TimW

Mahindra 6520 4WD with loader/backhoe and a Caterpiller E70 Excavator.  My mill is a Woodmizer LT40HD Wide 35hp Yanmar Diesel. An old Lull 644D-34 called Bull

Stephen1

Always something is right, but that's part of the fun! 
Looking forward to this years build.
IDRY Vacum Kiln, LT40HDWide, BMS250 sharpener/setter 742b Bobcat, TCM forklift, Sthil 026,038, 461. 1952 TEA Fergusan Tractor

thecfarm

Good luck with the building this year!!!
Model 6020-20hp Manual Thomas bandsaw,TC40A 4wd 40 hp New Holland tractor, 450 Norse Winch, Heatmor 400 OWB,YCC 1978-79

Thank You Sponsors!